- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ34701EWR2 (飛思卡爾半導體(中國)有限公司) 1.5A Switch-Mode Power Supply with Linear Regulator PDF資料下載
參數資料
| 型號： | MCZ34701EWR2 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 1.5A Switch-Mode Power Supply with Linear Regulator |
| 中文描述： | 1.5A的開關模式電源，線性穩壓器 |
| 文件頁數： | 24/39頁 |
| 文件大?。?/td> | 528K |
| 代理商： | MCZ34701EWR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
24
34701
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Standard Power Sequencing Control
Comparators monitor voltage differences between the
LDO (LDO pin) and the switcher (VOUT pin) outputs as
follows:
1.
LDO > VOUT + 1.9V, turn off LDO.
The LDO can be
forced off. This occurs whenever the LDO output
voltage exceeds the switcher output voltage by more
than 1.9V.
2.
LDO > VOUT + 2.0V, shunt LDO to ground.
If turning
off the LDO is insufficient and the LDO output voltage
exceeds the switcher output voltage by more than
2.0V, a 1.5
shunt MOSFET is turned on that
discharges the LDO load capacitor to ground. The
shunt MOSFET is used for switcher output shorts to
ground and for power down in case of VIN1
≠
VIN2
with the switcher output falling faster than the LDO.
3. LDO < VOUT + 1.9V cancel (2).
4.
LDO < VOUT + 1.8V, cancel (1) above, re-enable LDO.
Normal operation resumes when the LDO output
voltage is less than 1.8V above the switcher output
voltage.
5.
LDO < VOUT - 0.1V, turn off switcher.
The switcher
can be forced off. This occurs whenever the LDO is
less than VOUT - 0.1V.
6.
LDO < VOUT - 0.3V, turn on Sync (LS) MOSFET and
1.5
VOUT sink MOSFET.
The buck high side
MOSFET is forced off and the sync MOSFET is forced
on. This occurs when the switcher output voltage
exceeds the LDO output by more than 300mV.
7. LDO > VOUT - 0.3
V, cancel (6).
8.
LDO > VOUT - 0.1V, cancel (5).
Normal operation
resumes when LDO < VOUT - 0.1
V
Inverted Power Sequencing Control
Comparators monitor voltage differences between the
switcher (VOUT pin) and LDO (LDO pin) outputs as follows:
1.
VOUT > LDO + 1.8V, turn off VOUT .
The switcher
VOUT can be forced off. This occurs whenever the
VOUT output voltage exceeds the LDO output voltage
by more than 1.8V.
2.
VOUT > LDO + 2.0V, shunt VOUT to ground.
If turning
off the switcher VOUT is insufficient and the VOUT
output voltage exceeds the LDO output voltage by
more than 2.0V, a 1.5
shunt MOSFET and the
switcher synchronous MOSFET are turned on to
discharge the VOUT load capacitor to ground. The
shunt MOSFET and synchronous MOSFET are used
for LDO output shorts to ground and for power down in
case of VIN1
≠
VIN2 with LDO output falling faster than
the VOUT
3.
VOUT < LDO + 1.8V, cancel (1) and (2) above, re-
enable VOUT
Normal operation resumes when the
VOUT output voltage is less than 1.8V above the LDO
output voltage.
4. VOUT < LDO + 2.0
V, cancel (2)
5.
VOUT < LDO - 0.2V, turn off LDO.
The LDO can be
forced off. This occurs whenever the VOUT is less than
VLDO - 0.2V.
6.
VOUT < LDO - 0.3V, turn on the 1.5
LDO sink
MOSFET.
This occurs when the LDO output voltage
exceeds the VOUT output by more than 300mV.
7. VOUT < LDO - 0.2
V, cancel (6).
8.
VOUT < LDO - 0.1V, cancel (5).
Normal operation
resumes when VOUT > LDO - 0.1
V
.
STANDARD OPERATING MODE
Single 3.3V Supply, VIN = VIN1 = VIN2 = 3.3V
The 3.3V supplies the microprocessor I/O voltage, the
switcher supplies core voltage (e.g., 1.5V nominal), and the
LDO operates independently (see
Figure 17
, page
22
).
Power sequencing depends only on the normal switcher
intrinsic operation to control the buck high side MOSFET.
Power-up
When VIN is rising, initially VOUT is below the regulation
point and the Buck High-Side MOSFET is on. In order not to
exceed the 2.1 V differential requirement between the I/O
(VIN) and the core (VOUT), the switcher must start up at
2.1 V or less and be able to maintain the 2.1 V or less
differential. The maximum slew rate for V
IN
is 1.0 V/ms.
Power-Down
When VIN is falling, VOUT falls below the regulation point;
therefore, the buck high side MOSFET is on. In the case
where VOUT is falling faster than VIN, the buck high side
MOSFET attempts to maintain VOUT. In the case where VIN
is falling faster than VOUT, the buck high side MOSFET is
also on, and the VOUT load capacitor is discharged through
the buck high side MOSFET to VIN. Thus, provided VIN does
not fall too fast, the core voltage (VOUT) does not exceed the
I/O voltage (VIN) by more than a maximum of 0.4V.
Shorted Load
1.
VOUT shorted to ground.
This causes the I/O voltage
to exceed the core voltage by more than 2.1V. No load
protection.
2.
VIN shorted to ground.
Until the switcher load
capacitance is discharged, the core voltage exceeds
the I/O voltage by more than 0.4V. By the intrinsic
operation of the switcher, the load capacitor is
discharged rapidly through the buck high side
MOSFET to VIN.
3.
VOUT shorted to supply.
No load protection. 34701 is
protected by current limit and thermal shutdown.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ79076EG | Electronic Ignition Control Circuit |
| MD-S5007 | Analog IC |
| MD-S5008 | Analog IC |
| MD-S5010 | Analog IC |
| MD100 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ34702EW | 功能描述:低壓差穩壓器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCZ34702EWR2 | 功能描述:低壓差穩壓器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCZ36304201 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36305001 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36444401 | 制造商:LG Corporation 功能描述:Duct |
發布緊急采購，3分鐘左右您將得到回復。