- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33970EG (飛思卡爾半導體(中國)有限公司) Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms PDF資料下載
參數資料
| 型號： | MCZ33970EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms |
| 中文描述： | 雙計驅動集成電路與改進的阻尼算法 |
| 文件頁數： | 30/36頁 |
| 文件大?。?/td> | 430K |
| 代理商： | MCZ33970EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
30
33970
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
DEFAULT MODE
Default mode refers to the state of the 33970 after an
internal or external reset prior to SPI communication. An
internal reset occurs during V
DD
power-up or if V
PWR
falls
below 4.0 V. An external reset is initiated by the
RST
pin
driven to a logic [0]. With the exception of the RTZCR full step
time, all of the specific pin functions and internal registers will
operate as though all of the addressable configuration
register bits were set to logic [0]. This means, for example, all
of the outputs will be disabled after a power-up or external
reset, and SO flag ST6 is set, indicating an undervoltage
event. Anytime an external reset is exerted and the default is
restored, all configuration parameters (e.g., clock calibration,
maximum speed, RTZ parameters, etc.) are lost and must be
reloaded.
FAULT LOGIC REQUIREMENTS
The 33970 device indicates each of the following faults as
they occur:
Overtemperature fault
Undervoltage V
PWR
Overvoltage V
PWR
Clock out of spec
These fault bits remain enabled until they are clocked out
of the SO pin with a valid SPI message.
Overcurrent faults are not reported directly; however, it is
likely an overcurrent condition will become a thermal issue
and be reported.
OVERTEMPERATURE FAULT REQUIREMENTS
The 33970 incorporates overtemperature protection
circuitry, which shuts off the affected gauge driver when
excessive temperatures are detected. In the event of a
thermal overload, the affected gauge driver is automatically
disabled. The overtemperature fault is flagged via the OT0
and/or OT1 device status bits. The indicating flag continues
to be set until the affected gauge is successfully re-enabled,
provided the junction temperature has fallen to a temperature
below the hysteresis level.
OVERVOLTAGE FAULT REQUIREMENTS
The device is capable of surviving V
PWR
voltages within
the maximum specified in
Table 2
. V
PWR
levels resulting in
an Overvoltage Shutdown condition can result in uncertain
pointer positions. Therefore, the pointer position should be
re-calibrated. The master will be notified of an overvoltage
event via the SO pin if the device status is selected.
Overvoltage detection and notification occurs regardless of
whether the gauge(s) are enabled or disabled.
OVERCURRENT FAULT REQUIREMENTS
Output currents are limited to safe levels allowing the
device to rely on thermal shutdown to protect itself.
UNDERVOLTAGE FAULT REQUIREMENTS
Undervoltage V
PWR
conditions may result in uncertain
pointer positions. Therefore, the internal clock and the pointer
position may require re-calibration. The state machine
continues with V
PWR
voltage levels as low as 4.0 V; however,
the coil voltages may be clipped. The master can be notified
of an undervoltage event via the SO pin. Undervoltage
detection and notification are disabled if both outputs are
disabled.
RESET (SLEEP MODE)
The device can reset internally or externally. If the V
DD
level falls below the V
DDUV
level (refer to the Static Electrical
Characteristics table under
POWER INPUT
, page
5
), the
device resets and powers up in the Default mode. Similarly,
If the
RST
pin is driven to a logic [0], the device resets to its
default state. The device consumes the least amount of
current (I
DD
and I
PWR
) when the
RST
pin is logic 0]. This is
also referred to as the Sleep mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33976EG | Dual Gauge Driver with Configurable esponse Time |
| MCZ33977EG | Single Gauge Driver |
| MCZ33989EG | System Basis Chip with High-Speed CAN Transceiver |
| MCZ33990EF | Enhanced Class B Serial Transceiver |
| MCZ33991EG | Gauge Driver Integrated Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33970EG | 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GAUGE DRIVER SPI |
| MCZ33970EGR2 | 功能描述:馬達/運動/點火控制器和驅動器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33972AEK | 功能描述:接口 - 專用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33972AEK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multiple Switch Detection Interface with Suppressed Wake-up |
| MCZ33972AEKR2 | 功能描述:接口 - 專用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。