- 您現在的位置：買賣IC網 > PDF目錄385575 > MCR100 (ON SEMICONDUCTOR) Sensitive Gate Silicon Controlled Rectifiers(可控硅整流管) PDF資料下載
參數資料
| 型號： | MCR100 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Sensitive Gate Silicon Controlled Rectifiers(可控硅整流管) |
| 中文描述： | 敏感柵硅（可控硅整流管控整流器） |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 65K |
| 代理商： | MCR100 |
MCR100 Series
http://onsemi.com
5
TO92 EIA RADIAL TAPE IN FAN FOLD BOX OR ON REEL
H2A
H2A
H
F1
F2
P2
P2
P1
P
D
W
W1
L1
W2
H2B
H2B
T1
T
T2
H4H5
H1
L
Figure 7. Device Positioning on Tape
Specification
Inches
Millimeter
Min
Symbol
Item
Min
Max
Max
D
Tape Feedhole Diameter
0.1496
0.1653
3.8
4.2
D2
Component Lead Thickness Dimension
0.015
0.020
0.38
0.51
F1, F2
Component Lead Pitch
0.0945
0.110
2.4
2.8
H
Bottom of Component to Seating Plane
.059
.156
1.5
4.0
H1
Feedhole Location
0.3346
0.3741
8.5
9.5
H2A
Deflection Left or Right
0
0.039
0
1.0
H2B
Deflection Front or Rear
0
0.051
0
1.0
H4
Feedhole to Bottom of Component
0.7086
0.768
18
19.5
H5
Feedhole to Seating Plane
0.610
0.649
15.5
16.5
L
Defective Unit Clipped Dimension
0.3346
0.433
8.5
11
L1
Lead Wire Enclosure
0.09842
—
2.5
—
P
Feedhole Pitch
0.4921
0.5079
12.5
12.9
P1
Feedhole Center to Center Lead
0.2342
0.2658
5.95
6.75
P2
First Lead Spacing Dimension
0.1397
0.1556
3.55
3.95
T
Adhesive Tape Thickness
0.06
0.08
0.15
0.20
T1
Overall Taped Package Thickness
—
0.0567
—
1.44
T2
Carrier Strip Thickness
0.014
0.027
0.35
0.65
W
Carrier Strip Width
0.6889
0.7481
17.5
19
W1
Adhesive Tape Width
0.2165
0.2841
5.5
6.3
W2
Adhesive Tape Position
.0059
0.01968
.15
0.5
NOTES:
1. Maximum alignment deviation between leads not to be greater than 0.2 mm.
2. Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm.
3. Component lead to tape adhesion must meet the pull test requirements.
4. Maximum noncumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches.
5. Holddown tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive.
6. No more than 1 consecutive missing component is permitted.
7. A tape trailer and leader, having at least three feed holes is required before the first and after the last component.
8. Splices will not interfere with the sprocket feed holes.
相關PDF資料 |
PDF描述 |
|---|---|
| MCR12DSM | Sensitive Gate Silicon Controlled Rectifiers(可控硅整流管) |
| MCR12DSN | Sensitive Gate Silicon Controlled Rectifiers(可控硅整流管) |
| MCR12LD | Silicon Controlled Rectifiers(可控硅整流管) |
| MCR12LM | Silicon Controlled Rectifiers(可控硅整流管) |
| MCR12LN | Silicon Controlled Rectifiers(可控硅整流管) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCR100_07 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors |
| MCR100_1 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Thick film rectangular Low resistance series |
| MCR100_11 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Low Ohmic Thick Film Chip Resistors |
| MCR100_2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Low Ohmic Thick Film Chip Resistors |
| MCR100-003 | 功能描述:SCR 100V 800mA RoHS:否 制造商:STMicroelectronics 最大轉折電流 IBO:480 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態 RMS 電流 (It RMS): 正向電壓下降:1.6 V 柵觸發電壓 (Vgt):1.3 V 最大柵極峰值反向電壓:5 V 柵觸發電流 (Igt):35 mA 保持電流（Ih 最大值）:75 mA 安裝風格:Through Hole 封裝 / 箱體:TO-220 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。