- 您現在的位置：買賣IC網 > PDF目錄2097 > MCP3427-E/MF (Microchip Technology)IC ADC 16BIT I2C PROGBL 10-DFN PDF資料下載
參數資料
| 型號： | MCP3427-E/MF |
| 廠商： | Microchip Technology |
| 文件頁數： | 9/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT I2C PROGBL 10-DFN |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 120 |
| 位數： | 16 |
| 采樣率（每秒）： | 15 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-DFN-EP（3x3） |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個差分，單極 |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
2009 Microchip Technology Inc.
DS22226A-page 17
MCP3426/7/8
5.0
USING THE DEVICES
5.1
Operating Modes
The user operates the device by setting up the device
configuration register using a write command (see
Figure 5-3) and reads the conversion data using a read
command (see Figure 5-4 ). The device operates in two
modes:
(a)
Continuous
Conversion
Mode
or
(b) One-Shot Conversion Mode (single conversion).
This mode selection is made by setting the O/C bit in
the Configuration Register. Refer to Section 5.2
“Configuration Register” for more information.
5.1.1
CONTINUOUS CONVERSION
MODE (O/C BIT = 1)
The device performs a Continuous Conversion if the
O/C bit is set to logic “high”. Once the conversion is
completed, RDY bit is toggled to ‘0’ and the result is
placed at the output data register. The device
immediately begins another conversion and overwrites
the output data register with the most recent result.
The device clears the data ready flag (RDY bit = 0)
when the conversion is completed. The device sets the
ready flag bit (RDY bit = 1), if the latest conversion
result has been read by the Master.
When writing configuration register:
- Setting RDY bit in continuous mode does not
affect anything.
When reading conversion data:
- RDY bit = 0 means the latest conversion
result is ready.
- RDY bit = 1 means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion
result is ready.
5.1.2
ONE-SHOT CONVERSION MODE
(O/C BIT = 0)
Once the One-Shot Conversion (single conversion)
Mode is selected, the device performs only one
conversion, updates the output data register, clears the
data ready flag (RDY = 0), and then enters a low power
standby mode. A new One-Shot Conversion is started
again when the device receives a new write command
with RDY = 1.
When writing configuration register:
- The RDY bit needs to be set to begin a new
conversion in one-shot mode.
When reading conversion data:
- RDY bit = 0 means the latest conversion
result is ready.
- RDY bit = 1 means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion is
done.
This
One-Shot
Conversion
Mode
is
highly
recommended for low power operating applications
where the conversion result is needed by request on
demand. During the low current standby mode, the
device consumes less than 1 A maximum (or 300 nA
typical). For example, if the user collects 16-bit
conversion
data
once
a
second
in
One-Shot
Conversion mode, the device draws only about one-
fifteenth of the operating currents for the continuous
conversion
mode.
In
this
example,
the
device
consumes
approximately
9 A
(135 A
/
15 SPS = 9 A), when the device performs only one
conversion per second (1 SPS) in 16-bit conversion
mode with 3V power supply.
相關PDF資料 |
PDF描述 |
|---|---|
| MCP3550T-60E/MS | IC ADC 22BIT 2.7V 1CH 8MSOP |
| MCP6541RT-I/OT | IC COMP 1.6V PUSH-PULL SOT23-5 |
| MCP6546UT-I/LT | IC COMP 1.6V SNGL O-D SC70-5 |
| MCP6561UT-E/OT | IC COMP PUSH-PULL 1.8V SOT23-5 |
| MCP6566RT-E/OT | IC COMPARATOR O-D 1.8V SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3427-EMS | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-ESL | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-ESN | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-EST | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-EUN | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
發布緊急采購，3分鐘左右您將得到回復。