- 您現在的位置：買賣IC網 > PDF目錄2097 > MCP3427-E/MF (Microchip Technology)IC ADC 16BIT I2C PROGBL 10-DFN PDF資料下載
參數資料
| 型號： | MCP3427-E/MF |
| 廠商： | Microchip Technology |
| 文件頁數： | 14/56頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT I2C PROGBL 10-DFN |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 120 |
| 位數： | 16 |
| 采樣率（每秒）： | 15 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-DFN-EP（3x3） |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個差分，單極 |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
2009 Microchip Technology Inc.
DS22226A-page 21
MCP3426/7/8
TABLE 5-3:
ADDRESS BITS VS. ADDRESS
SELECTION PINS FOR
(MCP3427 AND MCP3428
ONLY) (NOTE1,2,3)
5.3.3
WRITING A CONFIGURATION BYTE
TO THE DEVICE
When the Master sends an address byte with the R/W
bit low (R/W = 0), the device expects one configuration
byte following the address. Any byte sent after this
second byte will be ignored. The user can change the
operating
mode
of
the
device
by
writing
the
configuration register bits.
If the device receives a write command with a new
configuration setting, the device immediately begins a
new conversion and updates the conversion data.
FIGURE 5-3:
Timing Diagram For Writing To The MCP3426/7/8.
I2C Device
Address Bits
Logic Status of Address
Selection Pins
A2
A1
A0
Adr0 Pin
Adr1 Pin
000
0 (Addr_Low)
001
0 (Addr_Low)
Float
010
0 (Addr_Low)
1 (Addr_High)
100
1 (Addr_High)
0 (Addr_Low)
101
1 (Addr_High)
Float
110
1 (Addr_High)
011
Float
0 (Addr_Low)
111
Float
1 (Addr_High)
000
Float
Note 1:
Float: (a) Leave pin without connecting to
anything (left floating), or (b) apply
Addr_Float voltage.
2:
The user can tie the pins to VSS or VDD:
- Tie to VSS for Addr_Low
- Tie to VDD for Addr_High
3:
See Addr_Low, Addr_High, and
Addr_Float parameters in Electrical
Characteristics Table.
9
1
9
1
Stop Bit by
11
0
1A2 A1 A0
R/W
ACK by
MCP3426/7/8
RDY
C1 C0
O/C
S1 S0 G1 G0
1st Byte:
2nd Byte:
Master
ACK by
MCP3426/7/8
Address Byte
Configuration Byte
Start Bit by
Master
with Write command
Note:
– Stop bit can be issued any time during writing.
– MCP3426/7/8 device code is 1101 (programmed at the factory).
– See Figure 5-1 for details in Address Byte.
SCL
SDA
(a) One-Shot Mode: 1
(b) Continuous Mode: not effected
相關PDF資料 |
PDF描述 |
|---|---|
| MCP3550T-60E/MS | IC ADC 22BIT 2.7V 1CH 8MSOP |
| MCP6541RT-I/OT | IC COMP 1.6V PUSH-PULL SOT23-5 |
| MCP6546UT-I/LT | IC COMP 1.6V SNGL O-D SC70-5 |
| MCP6561UT-E/OT | IC COMP PUSH-PULL 1.8V SOT23-5 |
| MCP6566RT-E/OT | IC COMPARATOR O-D 1.8V SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3427-EMS | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-ESL | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-ESN | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-EST | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3427-EUN | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
發布緊急采購，3分鐘左右您將得到回復。