- 您現在的位置：買賣IC網 > PDF目錄9815 > MCP3421A5T-E/OT (Microchip Technology)IC ADC 18BIT 3.75SPS SOT23-6 PDF資料下載
參數資料
| 型號： | MCP3421A5T-E/OT |
| 廠商： | Microchip Technology |
| 文件頁數： | 5/30頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT 3.75SPS SOT23-6 |
| 標準包裝： | 1 |
| 位數： | 18 |
| 采樣率（每秒）： | 3.75 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-23-6 |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，單極 |
| 配用： | MCP3421EV-ND - BOARD EVAL FOR MCP3421 SOT23-6 |
| 其它名稱： | MCP3421A5T-E/OTDKR |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
2006 Microchip Technology Inc.
DS22003B-page 13
MCP3421
FIGURE 5-1:
MCP3421 Address Byte.
5.3.2
READING DATA FROM THE DEVICE
When the Master sends a read command (R/W = 1),
the MCP3421 outputs the conversion data bytes and
configuration byte. Each byte consists of 8 bits with
one acknowledge (ACK) bit. The ACK bit after the
address byte is issued by the MCP3421 and the ACK
bits after each conversion data bytes are issued by the
Master.
When the device is configured for 18-bit conversion
mode, the device outputs three data bytes followed by
a configuration byte. The first 7 data bits in the first
data byte are the MSB of the conversion data. The
user can ignore the first 6 data bits, and take the 7th
data bit (D17) as the MSB of the conversion data. The
LSB of the 3rd data byte is the LSB of the conversion
data (D0).
If the device is configured for 12, 14, or 16 bit-mode, the
device outputs two data bytes followed by a
configuration byte. In 16 bit-conversion mode, the MSB
of the first data byte is the MSB (D15) of the conversion
data. In 14-bit conversion mode, the first two bits in the
first data byte can be ignored (they are the MSB of the
conversion data), and the 3rd bit (D13) is the MSB of
the conversion data. In 12-bit conversion mode, the
first four bits can be ignored (they are the MSB of the
conversion data), and the 5th bit (D11) of the byte
represents the MSB of the conversion data. Table 5-3
shows an example of the conversion data output of
each conversion mode.
The configuration byte follows the output data byte.
The device outputs the configuration byte as long as
the SCL pulses are received. The device terminates
the current outputs when it receives a Not-Acknowl-
edge (NAK), a repeated start or a stop bit at any time
during the output bit stream. It is not required to read
the configuration byte. However, the user may read the
configuration byte to check the RDY bit condition to
confirm whether the just received data bytes are
updated conversion data. The user may continuously
send clock (SCL) to repeatedly read the configuration
bytes to check the RDY bit status.
reading.
5.3.3
WRITING A CONFIGURATION BYTE
TO THE DEVICE
When the Master sends an address byte with the R/W
bit low (R/W = 0), the MCP3421 expects one
configuration byte following the address. Any byte sent
after this second byte will be ignored. The user can
change the operating mode of the device by writing the
configuration register bits.
If the device receives a write command with a new
configuration setting, the device immediately begins a
new conversion and updates the conversion data.
Start bit
Read/Write bit
Address Byte
R/W ACK
1
0
1
X
Device Code
Address Bits (Note 1)
Address
Acknowledge bit
Address
Note 1:
Specified by customer and programmed at the
factory. If not specified by the customer,
programmed to ‘
000’.
TABLE 5-3:
EXAMPLE OF CONVERSION DATA OUTPUT OF EACH CONVERSION MODE
Conversion
Mode
Conversion Data Output
18-bits
MMMMMMMD16 (1st data byte) - D15 ~ D8 (2nd data byte) - D7 ~ D0 (3rd data byte) - Configuration
byte
16-bits
MD14~D8 (1st data byte) - D7 ~ D0 (2nd data byte) - Configuration byte
14-bits
MMMD12~D8 (1st data byte) - D7 ~ D0 (2nd data byte) - Configuration byte
12-bits
MMMMMD10D9D8 (1st data byte) - D7 ~ D0 (2nd data byte) - Configuration byte
Note:
M is MSB of the data byte.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3077EESA/V+ | IC TXRX RS485/422 ESD 8SOIC |
| GTC06AF-24-12P | CONN PLUG 5POS STRAIGHT W/PINS |
| MAX13182EESD+ | IC TXRX RS-485 +5.0V ESD 14SOIC |
| D38999/24JD19SA | CONN RCPT 19POS JAM NUT W/SCKT |
| D38999/26JD18PC | CONN PLUG 18POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3421A6T-E/CH | 制造商:Microchip Technology 功能描述:18-BIT DELTA-SIGMA ADC, SINGLE 制造商:Microchip Technology Inc 功能描述:18-BIT DELTA-SIGMA ADC, SINGLE CHANNEL, 4SPS - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC ADC 18BIT I2C 4SPS SOT23-6 |
| MCP3421A6T-E/OT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3421A7T-E/CH | 制造商:Microchip Technology 功能描述:18-BIT DELTA-SIGMA ADC, SINGLE 制造商:Microchip Technology Inc 功能描述:18-BIT DELTA-SIGMA ADC, SINGLE CHANNEL, 4SPS - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC ADC 18BIT I2C 4SPS SOT23-6 |
| MCP3421A7T-E/OT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3421DM-BFG | 功能描述:數據轉換 IC 開發工具 MCP3421Battery Fuel Gauge Demo Brd RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。