參數資料
型號: MCF5232CAB80
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 80 MHz, RISC PROCESSOR, PQFP160
封裝: QFP-160
文件頁數: 20/76頁
文件大?。?/td> 2665K
代理商: MCF5232CAB80
MOTOROLA
MCF523x Integrated Microprocessor Hardware Specifications
27
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
Signal Primary Functions
2.2.14 Debug Support Signals
These signals are used as the interface to the on-chip JTAG controller and also to interface to the BDM logic.
DMA Timer 2 Input
DTIN2
Can be programmed to cause events to occur in the third platform
timer. It can either clock the event counter or provide a trigger to the
timer value capture logic.
This pin can also be configured as DMA request line signal, DREQ2,
or as GPIO.
I
DMA Timer 2 Output
DTOUT2
The output from the third platform timer.
This pin can also be configured as GPIO.
I
DMA Timer 3 Input
DTIN3
Can be programmed as an input that causes events to occur in the
fourth platform timer. This can either clock the event counter or
provide a trigger to the timer value capture logic.
This pin can also be configured as QSPI chip select 2 signal, UART 2
clear-to-send signal, U2CTS, or as GPIO.
I
DMA Timer 3 Output
DTOUT3
The output from the fourth platform timer.
This pin can also be configured as QSPI chip select 2 signal, UART 2
request-to-send signal, U2RTS, or as GPIO.
O
Table 15. Debug Support Signals
Signal Name
Abbreviation
Function
I/O
Test Reset
TRST
This active-low signal is used to initialize the JTAG logic
asynchronously.
I
Test Clock
TCLK
Used to synchronize the JTAG logic.
I
Test Mode Select
TMS
Used to sequence the JTAG state machine. TMS is sampled on the
rising edge of TCLK.
I
Test Data Input
TDI
Serial input for test instructions and data. TDI is sampled on the rising
edge of TCLK.
I
Test Data Output
TDO
Serial output for test instructions and data. TDO is three-stateable and
is actively driven in the shift-IR and shift-DR controller states. TDO
changes on the falling edge of TCLK.
O
Development Serial
Clock
DSCLK
Clocks the serial communication port to the BDM module during
packet transfers.
I
Breakpoint
BKPT
Used to request a manual breakpoint.
I
Table 14. DMA Timer Signals (continued)
Signal Name
Abbreviation
Function
I/O
相關PDF資料
PDF描述
MCF5232CVM100 32-BIT, 100 MHz, RISC PROCESSOR, PBGA196
MCF5271CVM150 32-BIT, 150 MHz, RISC PROCESSOR, PBGA196
MCF5270AB100 32-BIT, 100 MHz, RISC PROCESSOR, PQFP160
MCF5272CVF66 32-BIT, 66 MHz, RISC PROCESSOR, PBGA196
MCF5272VF66R2 32-BIT, 66 MHz, RISC PROCESSOR, PBGA196
相關代理商/技術參數
參數描述
MCF5232CVM100 功能描述:微處理器 - MPU MCF5232 V2CORE 64KSRAM RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MCF5232CVM100 制造商:Freescale Semiconductor 功能描述:Microprocessor IC
MCF5232CVM100J 功能描述:32位微控制器 - MCU V2CORE 64KSRAM RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
MCF5232CVM150 功能描述:微處理器 - MPU MCF5232 V2CORE 64KSRAM RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MCF5232CVM150J 功能描述:32位微控制器 - MCU V2CORE 64KSRAM RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT