參數資料
型號: MCF5232CAB80
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 80 MHz, RISC PROCESSOR, PQFP160
封裝: QFP-160
文件頁數: 18/76頁
文件大小: 2665K
代理商: MCF5232CAB80
MOTOROLA
MCF523x Integrated Microprocessor Hardware Specifications
25
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
Signal Primary Functions
2.2.11 Queued Serial Peripheral Interface (QSPI)
Table 12 describes QSPI signals.
2.2.12 UART Module Signals
The UART modules use the signals in this section for data. The baud rate clock inputs are not supported.
Table 12. Queued Serial Peripheral Interface (QSPI) Signals
Signal Name
Abbreviation
Function
I/O
QSPI Syncrhonous
Serial Output
QSPI_DOUT
Provides the serial data from the QSPI and can be programmed to be
driven on the rising or falling edge of QSPI_CLK. Each byte is sent
msb first.
This pin can also be configured as GPIO.
O
QSPI Synchronous
Serial Data Input
QSPI_DIN
Provides the serial data to the QSPI and can be programmed to be
sampled on the rising or falling edge of QSPI_CLK. Each byte is
written to RAM lsb first.
This pin can also be configured as GPIO or as I2C data signal
I2C_SDA.
I
QSPI Serial Clock
QSPI_CLK
Provides the serial clock from the QSPI. The polarity and phase of
QSPI_CLK are programmable. The output frequency is programmed
according to the following formula, in which n can be any value
between 1 and 255:
SPI_CLK = fsys/2 ÷ n
This pin can also be configured as GPIO or as I2C clock signal
I2C_SCL.
O
Synchronous
Peripheral Chip Selects
QSPI_CS[1:0] Provide QSPI peripheral chip selects that can be programmed to be
active high or low. QSPI_CS1 can also be configured as SDRAM
clock enable signal SD_CKE.
These pins can also be configured as GPIO.
O
Table 13. UART Module Signals
Signal Name
Abbreviation
Function
I/O
Transmit Serial Data
Output
U2TXD/U1TXD
/U0TXD
Transmitter serial data outputs for the UART modules. The output is
held high (mark condition) when the transmitter is disabled, idle, or in
the local loopback mode. Data is shifted out, lsb first, on this pin at the
falling edge of the serial clock source.
U1TXD can also be configured as Controller Area Network Transmit
data output CAN0TX.
U2TXD can also be configured as Controller Area Network Transmit
data output CAN1TX.
All pins can also be configured as GPIO.
O
相關PDF資料
PDF描述
MCF5232CVM100 32-BIT, 100 MHz, RISC PROCESSOR, PBGA196
MCF5271CVM150 32-BIT, 150 MHz, RISC PROCESSOR, PBGA196
MCF5270AB100 32-BIT, 100 MHz, RISC PROCESSOR, PQFP160
MCF5272CVF66 32-BIT, 66 MHz, RISC PROCESSOR, PBGA196
MCF5272VF66R2 32-BIT, 66 MHz, RISC PROCESSOR, PBGA196
相關代理商/技術參數
參數描述
MCF5232CVM100 功能描述:微處理器 - MPU MCF5232 V2CORE 64KSRAM RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MCF5232CVM100 制造商:Freescale Semiconductor 功能描述:Microprocessor IC
MCF5232CVM100J 功能描述:32位微控制器 - MCU V2CORE 64KSRAM RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
MCF5232CVM150 功能描述:微處理器 - MPU MCF5232 V2CORE 64KSRAM RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MCF5232CVM150J 功能描述:32位微控制器 - MCU V2CORE 64KSRAM RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT