參數資料
型號: MC705L16CFUE
廠商: Freescale Semiconductor
文件頁數: 113/146頁
文件大?。?/td> 0K
描述: IC MCU 8BIT EPROM 80-QFP
標準包裝: 84
系列: HC05
核心處理器: HC05
芯體尺寸: 8-位
速度: 2.1MHz
連通性: SPI
外圍設備: LCD,POR,WDT
輸入/輸出數: 16
程序存儲器容量: 16KB(16K x 8)
程序存儲器類型: OTP
RAM 容量: 512 x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 80-QFP
包裝: 托盤
MC68HC05L16 MC68HC705L16 Data Sheet, Rev. 4.1
Freescale Semiconductor
69
Chapter 8
Simple Serial Peripheral Interface (SSPI)
8.1 Introduction
The simple serial peripheral interface (SSPI) of the MC68HC05L16 is a master/slave synchronous serial
communication module.
SSPI uses a 3-wire protocol: data input, data output, and serial clock. In this format, the clock is not being
included in the data stream and must be provided as a separate signal.
When the SSPI is enabled (SPE = 1), bits 0–2 of port C become SDI (serial data in), SDO (serial data
out), and SCK (serial clocK) pins. The corresponding DDRC bit does not change the direction of the pin.
The MSTR bit decides the SSPI operation mode. The SCK pin is configured as output in master mode
and configured as input in slave mode.
The DORD bit in the serial peripheral control register (SPCR) selects the data transmission order. When
DORD is set, the least significant bit (LSB) of serial data is shifted out/in first. When the DORD is clear,
serial data is shifted from/to the most significant bit (MSB).
Master serial clock speed is selected by the SPR bit in the SPCR. An interrupt may be generated by the
completion of a transfer.
8.2 Features
Features of the SSPI are:
Full-duplex, 3-wire synchronous transfers
Master or slave operation
Programmable data transmission order, LSB or MSB first
1.05-MHz (maximum) transmission bit frequency at 2.1-MHz CPU bus frequency at 5 Vdc
Two programmable transmission bit rates
End-of-transmission interrupt flag
Wakeup from stop mode (slave mode only)
8.3 Functional Descriptions
In master mode, the clock start logic is triggered by the CPU (detection of a CPU write to the 8-bit shift
register (SPDR)). The SCK is based on the internal processor clock. This clock is also used in the 3-bit
counter and 8-bit shift register. See Figure 8-2.
When data is written to the 8-bit shift register of the master device, it is then shifted out to the SDO pin for
application to the slave device. At the same time, data applied from the slave device via the SDI pin is
shifted into the 8-bit shift register.
相關PDF資料
PDF描述
MC705X32VFUE IC MCU 8BIT 32K FLASH 64-QFP
MC711P2CFNE3 IC MCU 8BIT 84-PLCC
MC7410VU450NE IC MPU RISC 32BIT 360-FCCBGA
MC7447AVU1333LB IC MPU RISC 32BIT 360-BGA
MC7448VS600ND IC MPU RISC 600MHZ 360-FCCLGA
相關代理商/技術參數
參數描述
MC705P6ACDWE 功能描述:8位微控制器 -MCU MCU 176 BYTES RAM A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705P6ACDWE 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MC705P6ACDWER 功能描述:IC MCU 8BIT EPROM 28-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 標準包裝:1 系列:AVR® ATmega 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C,SPI,UART/USART 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:32 程序存儲器容量:32KB(16K x 16) 程序存儲器類型:閃存 EEPROM 大小:1K x 8 RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:44-TQFP 包裝:剪切帶 (CT) 其它名稱:ATMEGA324P-B15AZCT
MC705P6ACPE 功能描述:8位微控制器 -MCU HC705P6A 176 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705P6AMDWE 功能描述:8位微控制器 -MCU MCU 176 BYTES RAM EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT