參數資料
型號： MC68711E20MFNE3
廠商： Freescale Semiconductor
文件頁數： 118/138頁
文件大?。?/td> 0K
描述： IC MCU 8BIT 52-PLCC
標準包裝： 23
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 4MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 38
程序存儲器容量： 20KB（20K x 8）
程序存儲器類型： OTP
EEPROM 大?。?/td> 512 x 8
RAM 容量： 768 x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 52-LCC（J 形引線）
包裝： 管件
Serial Peripheral Interface (SPI)
MC68HC711D3 Data Sheet, Rev. 2.1
80
Freescale Semiconductor
7.5.2 Master Out/Slave In (MOSI)
The MOSI line is the second of the two unidirectional serial data signals. It is an output from a master
device and an input to a slave device. The master device places data on the MOSI line a half-cycle before
the clock edge that the slave device uses to latch the data.
7.5.3 Serial Clock (SCK)
SCK, an input to a slave device, is generated by the master device and synchronizes data movement in
and out of the device through the MOSI and MISO lines. Master and slave devices are capable of
exchanging a byte of information during a sequence of eight clock cycles.
Four possible timing relationships can be chosen by using control bits CPOL and CPHA in the serial
peripheral control register (SPCR). Both master and slave devices must operate with the same timing.
The SPI clock rate select bits, SPR1 and SPR0, in the SPCR of the master device, select the clock rate.
In a slave device, SPR1 and SPR0 have no effect on the operation of the SPI.
7.5.4 Slave Select (SS)
The SS input of a slave device must be externally asserted before a master device can exchange data
with the slave device. SS must be low before data transactions and must stay low for the duration of the
transaction.
The SS line of the master must be held high. If it goes low, a mode fault error flag (MODF) is set in the
serial peripheral status register (SPSR). To disable the mode fault circuit, write a 1 in bit 5 of the port D
data direction register. This sets the SS pin to act as a general-purpose output. The other three lines are
dedicated to the SPI whenever the serial peripheral interface is on.
The state of the master and slave CPHA bits affects the operation of SS. CPHA settings should be
identical for master and slave. When CPHA = 0, the shift clock is the OR of SS with SCK. In this clock
phase mode, SS must go high between successive characters in an SPI message. When CPHA = 1, SS
can be left low between successive SPI characters. In cases where there is only one SPI slave MCU, its
SS line can be tied to VSS as long as only CPHA = 1 clock mode is used.
7.6 SPI System Errors
Two system errors can be detected by the SPI system. The first type of error arises in a multiple-master
system when more than one SPI device simultaneously tries to be a master. This error is called a mode
fault. The second type of error, write collision, indicates that an attempt was made to write data to the
SPDR while a transfer was in progress.
When the SPI system is configured as a master and the SS input line goes to active low, a mode fault
error has occurred — usually because two devices have attempted to act as master at the same time. In
cases where more than one device is concurrently configured as a master, there is a chance of contention
between two pin drivers. For push-pull CMOS drivers, this contention can cause permanent damage. The
mode fault attempts to protect the device by disabling the drivers. The MSTR control bit in the SPCR and
all four DDRD control bits associated with the SPI are cleared. An interrupt is generated subject to
masking by the SPIE control bit and the I bit in the CCR.
Other precautions may need to be taken to prevent driver damage. If two devices are made masters at
the same time, mode fault does not help protect either one unless one of them selects the other as slave.
The amount of damage possible depends on the length of time both devices attempt to act as master.
相關PDF資料
PDF描述
HCE103MBCCJ0KR CAP CER 10000PF 3KV 20% RADIAL
MC68HC705C9ACFNE IC MCU 8BIT 44-PLCC
VI-B5P-CU-F3 CONVERTER MOD DC/DC 13.8V 200W
MC68HC705C9AFNE IC MCU 8BIT 44-PLCC
VI-B5N-CU-F2 CONVERTER MOD DC/DC 18.5V 200W
相關代理商/技術參數
參數描述
MC68711E20MFNE3R 功能描述:IC MCU 8BIT 52-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:1 系列:AVR® ATmega 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，SPI，UART/USART 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:32 程序存儲器容量:32KB（16K x 16） 程序存儲器類型:閃存 EEPROM 大小:1K x 8 RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:44-TQFP 包裝:剪切帶 (CT) 其它名稱:ATMEGA324P-B15AZCT
MC68711E20VFNE2 功能描述:8位微控制器 -MCU 8B 20K EPROM 768RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC6875 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875A 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
MC6875AL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*