參數資料
型號： MC4GH01GNMCA-2SA00
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： SAMSUNG MultiMediaCard
中文描述： 三星多媒體
文件頁數： 79/102頁
文件大?。?/td> 1384K
代理商： MC4GH01GNMCA-2SA00
MultiMediaCard
TM
79
Sep.22.2005
Revision 0.3
Introduction
The SPI mode consists of a secondary, optional communication protocol which is offered by Flash-based MultiMedi-
aCards. This mode is a subset of the MultiMediaCard protocol, designed to communicate with a SPI channel, commonly
found in Motorola’s (and lately a few other vendors’) microcontrollers. The interface is selected during the first reset com-
mand after power up (CMD0) and cannot be changed once the part is powered on.
The SPI standard defines the physical link only, and not the complete data transfer protocol. The MultiMediaCard SPI
implementation uses a subset of the MultiMediaCard protocol and command set. It is intended to be used by systems
which typically require one card and have lower data transfer rates (compared to MultiMediaCard protocol based sys-
tems). From the application point of view, the advantage of the SPI mode is the capability of using an off-the-shelf host,
hence reducing the design-in effort to minimum. The disadvantage is the loss of performance of the SPI mode versus Mul-
tiMediaCard mode (lower data transfer rate, hardware CS, etc.).
7.1 SPI Interface Concept
The Serial Peripheral Interface (SPI) is a general purpose synchronous serial interface originally found on certain Motorola
microcontrollers. A virtually identical interface can now be found on certain TI and SGS Thomson microcontrollers as well.
The MultiMediaCard SPI interface is compatible with SPI hosts available on the market. As in any other SPI device, the
MultiMediaCard SPI channel consists of the following four signals:
CS
: Host to card Chip Select signal.
CLK
:Host to card clock signal
DataIn
:Host to card data signal.
DataOut
: Card to host data signal.
Another SPI common characteristic is byte transfers, which is implemented in the card as well. All data tokens are multi-
ples of bytes (8 bit) and always byte aligned to the CS signal.
7.2 SPI Bus Topology
The card identification and addressing methods are replaced by a hardware Chip Select (CS) signal. There are no broad-
cast commands. For every command, a card (slave) is selected by asserting (active low) the CS signal (see Figure ).
The CS signal must be continuously active for the duration of the SPI transaction (command, response and data). The
only exception occurs during card programming, when the host can de-assert the CS signal without affecting the program-
ming process.
The bidirectional CMD and DAT lines are replaced by unidirectional
dataIn
and
dataOut
signals.
The MultiMediaCard pin assignment in SPI mode (compared to MultiMediaCard mode) is given in Table 7-1.
7. SPI Mode
相關PDF資料
PDF描述
MC4GH02GNMCA-2SA00 SAMSUNG MultiMediaCard
MC206 THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT
MC2300 Navigator Motion Processor
MC26LS30 Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers
MC26LS30D CABLE GLAND, PG29
相關代理商/技術參數
參數描述
MC4GH02GNMCA-2SA00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard
MC4M 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM
MC-4-MALE 制造商:Multi-Contact USA 功能描述:
MC4MANUAL 制造商:Omron Corporation 功能描述:
MC-4R128CEE6B 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*