- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH01GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH01GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 44/102頁 |
| 文件大?。?/td> | 1384K |
| 代理商： | MC4GH01GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
44
Sep.22.2005
Revision 0.3
6.2.1 Command Sets And Extended Settings
The card operates in a given command set, by default, after a power cycle or reset by CMD0, it is the MultiMediaCard
standard command set, using a single data line, DAT0. The host can change the active command set by issuing the
SWITCH command (CMD6) with the ‘Command Set’ access mode selected.
The supported command sets, as well as the currently selected command set, are defined in the EXT_CSD register. The
EXT_CSD register is divided in two segments, a Properties segment and a Modes segment. The Properties segment con-
tains information about the card capabilities. The Modes segment reflects the current selected modes of the card.
The host reads the EXT_CSD register by issuing the SEND_EXT_CSD command. The card sends the EXT_CSD register
as a block of data, 512 bytes long. Any reserved, or write only field, reads as ‘0’.
The host can write the Modes segment of the EXT_CSD register by issuing a SWITCH command and setting one of the
access modes. All three modes access and modify one of the EXT_CSD bytes, the byte pointed by
the Index field
1
Table 6-2 : EXT_CSD Access Modes
The SWITCH command can be used either to write the EXT_CSD register or to change the command set. If the SWITCH
command is used to change the command set, the Index and Value field are ignored, and the EXT_CSD is not written. If
the SWITCH command is used to write the EXT_CSD register, the Cmd Set field is ignored, and the command set
remains unchanged.
The SWITCH command response is of type R1b, therefore, the host should read the card status, using SEND_STATUS
command, after the busy signal is de-asserted, to check the result of the SWITCH operation.
6.2.2 High Speed Mode Selection
After the host verifies that the card complies with version 4.0, or higher, of this standard, it has to enable the high speed
mode timing in the card, before changing the clock frequency to a frequency higher than 20MHz.
After power-on, or software reset, the interface timing of the card is set as specified in Table 5-7, Chapter 5. For the host to
change to a higher clock frequency, it has to enable the high speed interface timing. The host uses the SWITCH command
to write 0x01 to the HS_TIMING byte, in the Modes segment of the EXT_CSD register.
The valid values for this register are defined in ’HS_TIMING’, in page 37. If the host tries to write an invalid value, the
HS_TIMING byte is not changed, the high speed interface timing is not enabled, and the SWITCH_ERROR bit is set.
6.2.3 Power Class Selection
After the host verifies that the card complies with version 4.0, or higher, of this standard, it may change the power class of
the card.
After power-on, or software reset, the card power class is class 0, which is the default, minimum current consumption
class for the card type, either High Voltage or Dual voltage card. The PWR_CL_ff_vvv bytes, in the EXT_CSD register,
reflect the power consumption levels of the card, for a 4 bits bus, an 8 bit bus, at the supported clock frequencies (26MHZ
or 52MHz).
The host reads this information, using the SEND_EXT_CSD command, and determines if it will allow the card to use a
higher power class. If a power class change is needed, the host uses the SWITCH command to write the POWER_CLASS
byte, in the Modes segment of the EXT_CSD register.
The valid values for this register are defined in ’PWR_CL_ff_vvv’, in page 84 If the host tries to write an invalid value, the
POWER_CLASS byte is not changed and the SWITCH_ERROR bit is set.
Access Bits
Access Name
Operation
00
Command Set
The command set is changed according to the Cmd Set field of the argument
01
Set Bits
The bits in the pointed byte are set, according to the ‘1’ bits in the Value field.
10
Clear Bits
The bits in the pointed byte are cleared, according to the ‘1’ bits in the Value field.
11
Write Byte
The Value field is written into the pointed byte.
1.The Index field can contain any value from 0-255, but only values 0-191 are valid values. If the Index value is in the 192-255 range
the card does not perform any modification and the SWITCH_ERROR status bit is set.
相關PDF資料 |
PDF描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。