OPERATIONAL MODES Figure 11. Reset and WDOG" />
參數資料
型號： MC33889BDW
廠商： Freescale Semiconductor
文件頁數： 24/59頁
文件大?。?/td> 0K
描述： IC SYSTEM BASE W/CAN 28-SOIC
標準包裝： 1
控制器類型： 系統基礎芯片
接口： CAN
電源電壓： 5.5 V ~ 18 V
電流 - 電源： 45mA
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 28-SOIC W
包裝： 管件
Analog Integrated Circuit Device Data
30
Freescale Semiconductor
33889
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Figure 11. Reset and WDOG Function Diagram
DEBUG MODE APPLICATION HARDWARE AND SOFTWARE DEBUG WITH THE SBC.
When the SBC is mounted on the same printed circuit board as the micro controller, it supplies both application software and
the SBC with a dedicated routine that must be debugged. The following features allow the user to debug the software by disabling
the SBC internal software watchdog timer.
DEVICE POWER UP, RESET PIN CONNECTED TO VDD1
At SBC power up, the VDD1 voltage is provided, but if no SPI communication occurs to configure the device, a reset occurs
every 350 ms. In order to allow software debugging and avoid an MCU reset, the Reset pin can be connected directly to VDD1
by a jumper.
DEBUG MODES WITH SOFTWARE WATCHDOG DISABLED THOUGH SPI (NORMAL DEBUG, STANDBY DEBUG AND
STOP DEBUG)
The software watchdog can be disabled through the SPI. In order to avoid unwanted watchdog disables, and to limit the risk
of disabling the watchdog during an SBC normal operation, the watchdog disable has to be performed with the following
sequence:
Step 1) Power down the SBC
Step 2) Power up the SBC (The BATFAIL bit is set, and the SBC enters normal request mode)
Step 3) Write to the TIM1 register to allow the SBC to enter Normal mode
Step 4) Write to the MCR register with data 0000 (this enables the debug mode). (Complete SPI byte: 000 1 0000)
Step 5) Write to the MCR register normal debug (0001 x101), stand-by debug (0001 x110), or Stop debug (0001 x111)
While in debug mode, the SBC can be used without having to clear the W/D on a regular basis to facilitate software and
hardware debugging.
Step 6) To leave the debug mode, write 0000 to the MCR register.
To avoid entering the debug mode after a power up, first read the BATFAIL bit (MCR read) and write 0000 into the MCR.
Figure 12 illustrates entering the debug mode.
RESET
WDOG
VDD1
SPI
SPI CS
Watchdog timeout
Watchdog register addressed
Watchdog
period
W/D clear
相關PDF資料
PDF描述
MC33889DPEG IC SYSTEM BASE W/CAN 28SOIC
MC33972TEWR2 IC SWITCH DETECT SPI 32-SOIC
MC33975TEKR2 IC SWITCH DETECT MULT 32-SOIC
MC33989DWR2 IC SYSTEM BASE W/CAN 28-SOIC
MC3488ADR2G IC LINE DRIVER DUAL EIA 8-SOIC
相關代理商/技術參數
參數描述
MC33889BDWR2 功能描述:網絡控制器與處理器 IC SBC LIGHT PASS 3.3 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33889BPEG 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP WITH LOW SPEED FAULT TOLERANT CAN INTERFACE 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Bulk 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC
MC33889BPEGR2 制造商:Freescale Semiconductor 功能描述:CAN 125Kbps Sleep/Stop 9V/12V/15V T/R 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Tape and Reel 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC
MC33889DDW 功能描述:網絡控制器與處理器 IC SBC LIGHT REV D RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33889DDWR2 功能描述:網絡控制器與處理器 IC SBC LIGHT REV D RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*