參數資料
型號： MC2300
廠商： Electronic Theatre Controls, Inc.
英文描述： Navigator Motion Processor
中文描述： 導航運動處理器
文件頁數： 38/59頁
文件大小： 1925K
代理商： MC2300
MC2300 Technical Specifications
38
6 Application Notes
6.1
Design Tips
The following are recommendations for the design of circuits that utilize a PMD Motion Processor.
Serial Interface
The serial interface is a convenient interface that can be used before host software has been written
to communicate through the parallel interface. It is recommended that even if the serial interface is
not utilized as a standard communication interface, that the serial receive and transmit signals are
brought to test points so that they may be connected during initial board configuration/debugging.
This is especially important during the prototype phase. The serial receive line should include a pull-
up resistor to avoid spurious interrupts when it is not connected to a transceiver.
If the serial configuration decode logic is not implemented (see section 6.3) and the serial interface
may be used for debugging as mentioned above, the CP data bus should be tied high. This places the
serial interface in a default configuration of 9600,n,8,1 after power on or reset.
Controlling PWM output during reset
When the motion processor is in a reset state (when the reset line is held low) or immediately after a
power on, the PWM outputs can be in an unknown state, causing undesirable motor movement. It is
recommended that the enable line of any motor amplifier be held in a disabled state by the host
processor or some logic circuitry until communication to the motion processor is established. This
can be in the form of a delay circuit on the amplifier enable line after power up, or the enable line can
be ANDed with the CP reset line.
Reducing noise and power consumption
To reduce the emission of electrical noise and reduce power consumption (caused by floating inputs),
all unused input signals can be tied through a resistor to Vcc or directly to GND. The following CP
pins can be tied if not used: 45, 48, 68-70, 73, 90, 91, 101, 102, 105, 107-109, 78-81.
Parallel word encoder input
When using parallel word input for motor position, it is useful to also decode this information into
the User I/O space. This allows the current input value to be read using the chip instruction ReadIO
for diagnostic purposes.
Using a non standard system clock frequency
It is often desirable to share a common clock among several components in a design. In the case of
the PMD Motion Processors it is possible to use a clock below the standard value of 40MHz. In this
case all system frequencies will be reduced as a fraction of the input clock verses the standard
40MHz clock. The list below shows the affected system parameters:-
Serial baud rate
相關PDF資料
PDF描述
MC26LS30 Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers
MC26LS30D CABLE GLAND, PG29
MC26LS30DR2 Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers
MC28B 28 Lead Ceramic Small Outline Package, EPROM NS Package
MC33060ADG Fixed Frequency, PWM, Voltage Mode Single Ended Controllers
相關代理商/技術參數
參數描述
MC2307 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Open Carrier Double-Balanced Mixer For Microwave Telecommunications
MC2307-2 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Open Carrier Double-Balanced Mixer For Microwave Telecommunications
MC230B 制造商:Panasonic Industrial Company 功能描述:BELT MC-230B PANASONIC
MC-230B 制造商:Panasonic Industrial Company 功能描述:BELT
MC2310 制造商:M/A-COM Technology Solutions 功能描述:RF MIXER 制造商:M/A-COM Technology Solutions 功能描述:Up/Down Conv Mixer 7GHz 4-Pin
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*