參數資料
型號: MC2300
廠商: Electronic Theatre Controls, Inc.
英文描述: Navigator Motion Processor
中文描述: 導航運動處理器
文件頁數: 36/59頁
文件大?。?/td> 1925K
代理商: MC2300
MC2300 Technical Specifications
36
CP chip
Pin Name and
number
PosLim3/
Synch
Direction
Description
54
input/output
On the MC2340 chipset, this pin is the positive-side (forward) travel limit switch
for axis#3. On the MC2320 and MC2310 chipsets this pin is not used.
On the MC23x3 chipset, this pin is the synchronization signal. In the disabled
mode, the pin is configured as an input and is not used. In the master mode, the
pin outputs a synchronization pulse that can be used by slave nodes or other
devices to synchronize with the internal chip cycle of the master node. In the
slave mode, the pin is configured as an input and a pulse on the pin synchronizes
the internal chip cycle.
WARNING! If a valid axis limit pin is not used, its signal should
be tied high.
NC/PosLim3
45
input
On the MC23x0 chipset, this pin is not used.
On the MC2343 chipset, this pin is the positive-side (forward) travel limit switch
for axis#3. On the MC2323 and MC2313 chipsets this pin is not used.
WARNING! If a valid axis limit pin is not used, its signal should
be tied high.
NegLim1
NegLim2
NegLim3
NegLim4
64
66
55
51
input
These signals provide inputs from the negative-side (reverse) travel limit
switches. On power-up or
Reset
these signals default to active
low
interpretation,
but the interpretation can be set explicitly using the
SetSignalSense
instruction.
For MC2340 all 4 pins are valid. For MC2320 only
NegLim1
and
NegLim2
are
valid. For MC2310 only
NegLim1
is valid.
WARNING! If a valid axis pin is not used, its signal must be tied
high. NegLim1 is an output during device reset and as such any
connection to GND or V
cc
must be via a series resistor.
Invalid axis pins may also be left unconnected.
Each of these pins can be conditioned to track the state of any bit in the Status
registers associated with its axis.
For MC2340 all 4 pins are valid. For MC2320 only
AxisOut1
and
AxisOut2
are
valid. For MC2310 only
AxisOut1
is valid.
Invalid or unused pins may be left unconnected.
These are general-purpose programmable inputs. They may be used as a
breakpoint input, to stop a motion axis, or to cause an UPDATE to occur.
For MC2340 all 4 pins are valid. For MC2320 only
AxisIn1
and
AxisIn2
are valid.
For MC2310 only
AxisIn1
is valid.
Invalid or unused pins may be left unconnected.
Hall sensor inputs. Each set (A, B, and C) of signals encodes 6 valid states as
follows: A on, A and B on, B on, B and C on, C on, C and A on. A sensor is
defined as being on when its signal is
high
.
Note: These signals should only be connected to Hall sensors that are mounted
at a 120° offset. Schemes which provide Hall signals 60° apart will not work.
For MC2340 all 12 pins are valid. For MC2320 only the first six pins (axes 1 and
2) are valid. For MC2310 only the first three pins (axis 1) are valid.
Invalid or unused pins may be left unconnected.
AxisOut1
AxisOut2
AxisOut3
AxisOut4
94
95
96
97
output
AxisIn1
AxisIn2
AxisIn3
AxisIn4
72
100
106
67
input
Hall1A
Hall1B
Hall1C
Hall2A
Hall2B
Hall2C
Hall3A
Hall3B
Hall3C
Hall4A
Hall4B
Hall4C
73
90
91
101
102
105
107
108
109
68
69
70
Input
相關PDF資料
PDF描述
MC26LS30 Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers
MC26LS30D CABLE GLAND, PG29
MC26LS30DR2 Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers
MC28B 28 Lead Ceramic Small Outline Package, EPROM NS Package
MC33060ADG Fixed Frequency, PWM, Voltage Mode Single Ended Controllers
相關代理商/技術參數
參數描述
MC2307 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Open Carrier Double-Balanced Mixer For Microwave Telecommunications
MC2307-2 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Open Carrier Double-Balanced Mixer For Microwave Telecommunications
MC230B 制造商:Panasonic Industrial Company 功能描述:BELT MC-230B PANASONIC
MC-230B 制造商:Panasonic Industrial Company 功能描述:BELT
MC2310 制造商:M/A-COM Technology Solutions 功能描述:RF MIXER 制造商:M/A-COM Technology Solutions 功能描述:Up/Down Conv Mixer 7GHz 4-Pin