參數資料
型號: MB9AF312LPMC1
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP64
封裝: 0.50 MM PITCH, PLASTIC, LQFP-64
文件頁數: 6/114頁
文件大小: 1357K
代理商: MB9AF312LPMC1
103
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
16.5
Counter Unit
The main part of the 16-bit Timer/Counter is the programmable 16-bit bi-directional counter unit. Figure 16-2 shows a block
diagram of the counter and its surroundings.
Figure 16-2. Counter Unit Block Diagram
Signal description (internal signals):
Count
Increment or decrement TCNT1 by 1.
Direction
Select between increment and decrement.
Clear
Clear TCNT1 (set all bits to zero).
clkT1
Timer/Counter clock.
TOP
Signalize that TCNT1 has reached maximum value.
BOTTOM
Signalize that TCNT1 has reached minimum value (zero).
The 16-bit counter is mapped into two 8-bit I/O memory locations: Counter high (TCNT1H) containing the upper eight bits of
the counter, and counter low (TCNT1L) containing the lower eight bits. The TCNT1H register can only be indirectly accessed
by the CPU. When the CPU does an access to the TCNT1H I/O location, the CPU accesses the high byte temporary register
(TEMP). The temporary register is updated with the TCNT1H value when the TCNT1L is read, and TCNT1H is updated with
the temporary register value when TCNT1L is written. This allows the CPU to read or write the entire 16-bit counter value
within one clock cycle via the 8-bit data bus. It is important to notice that there are special cases of writing to the TCNT1
register when the counter is counting that will give unpredictable results. The special cases are described in the sections
where they are of importance.
Depending on the mode of operation used, the counter is cleared, incremented, or decremented at each timer clock (clkT1).
The clkT1 can be generated from an external or internal clock source, selected by the clock select bits (CS12:0). When no
clock source is selected (CS12:0 = 0) the timer is stopped. However, the TCNT1 value can be accessed by the CPU,
independent of whether clkT1 is present or not. A CPU write overrides (has priority over) all counter clear or count operations.
The counting sequence is determined by the setting of the waveform generation mode bits (WGM13:0) located in the
Timer/Counter control registers A and B (TCCR1A and TCCR1B). There are close connections between how the counter
behaves (counts) and how waveforms are generated on the output compare outputs OC1x. For more details about
advanced counting sequences and waveform generation, see Section 16.9 “Modes of Operation” on page 108.
The Timer/Counter overflow flag (TOV1) is set according to the mode of operation selected by the WGM13:0 bits. TOV1 can
be used for generating a CPU interrupt.
BOTTOM
TOP
TOVn
(Int. Req.)
DATA BUS (8-bit)
Control Logic
TCNTnH (8-bit)
TCNTnH (16-bit Counter)
TCNTnL (8-bit)
TEMP (8-bit)
clkTn
Clear
Count
Direction
Edge
Detector
(from Prescaler)
Clock Select
Tn
相關PDF資料
PDF描述
MB9AF312MPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80
MB9AF312LPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP64
MB9AF311NPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100
MB9AF316NPMC RISC MICROCONTROLLER, PQFP100
MB9AF314NPMC RISC MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB9AF314LAPMC1-G-JNE2 制造商:FUJITSU 功能描述:
MB9AF314LAPMC-G-JNE2 制造商:Fujitsu 功能描述:Bulk
MB9AF314LAQN-G-AVE2 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 256KB (256K x 8) FLASH 64-QFN Exposed Pad (9x9) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包裝:托盤 零件狀態:有效 核心處理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 連接性:CSIO,I2C,LIN,UART/USART,USB 外設:DMA,LVD,POR,PWM,WDT I/O 數:51 程序存儲容量:256KB(256K x 8) 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:32K x 8 電壓 - 電源(Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 9x12b 振蕩器類型:內部 工作溫度:-40°C ~ 105°C(TA) 封裝/外殼:64-VFQFN 裸露焊盤 供應商器件封裝:64-QFN 裸露焊盤(9x9) 標準包裝:260
MB9AF314LPMC1-ESE1 制造商:FUJITSU 功能描述:
MB9AF314LPMC1-GE1 制造商:FUJITSU 功能描述: