- 您現在的位置：買賣IC網 > PDF目錄2012 > MAX9867ETJ+T (Maxim Integrated Products)IC STEREO AUD CODEC LP 32TQFN-EP PDF資料下載
參數資料
| 型號： | MAX9867ETJ+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 38/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC STEREO AUD CODEC LP 32TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 立體聲音頻 |
| 數據接口： | I²C，串行 |
| 分辨率（位）： | 18 b |
| ADC / DAC 數量： | 2 / 2 |
| 三角積分調變： | 是 |
| 動態范圍，標準 ADC / DAC (db)： | 85 / 90 |
| 電壓 - 電源，模擬： | 1.65 V ~ 1.95 V |
| 電壓 - 電源，數字： | 1.65 V ~ 1.95 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
MAX9867
Ultra-Low Power Stereo Audio Codec
______________________________________________________________________________________
43
Mode Configuration
The MAX9867 includes circuitry to minimize click-and-
pop during volume changes, detect headsets, and con-
figure the headphone amplifier mode. Both volume
slewing and zero-crossing detection are included to
ensure click-and-pop free volume transitions. Table 16
is the mode configuration register.
Headset Detection Overview
The MAX9867 features headset detection that can detect
the insertion and removal of a jack as well as the load
type. When a jack is detected, an interrupt on IRQ can be
triggered to alert the microcontroller of the event. Figure 7
shows the typical configuration for jack detection.
Sleep-Mode Headset Detection
When the MAX9867 is in shutdown and the power supply
is available, sleep-mode headset detection can be
enabled to detect jack insertion. Sleep mode applies a
4A pullup current to JACKSNS/AUX and LOUTP that
forces the voltage on JACKSNS/AUX and LOUTP to
AVDD when no load is applied. When a jack is inserted,
either JACKSNS, LOUTP (assuming the headphone
amplifier is not configured in single-ended mode), or both
are loaded sufficiently to reduce the output voltage to
nearly 0V and clear the JKSNS or LSNS bits, respectively.
The change in the LSNS and JKSNS bits sets JDET and
triggers an interrupt on IRQ if IJDET is set. The interrupt
signals the microcontroller that a jack has been inserted,
allowing the microcontroller to respond as desired.
Powered-On Headset Detection
When the MAX9867 is in normal operation and the micro-
phone interface is enabled, jack insertion and removal can
be detected through the JACKSNS/AUX pin. As shown in
Figure 7, VMIC is pulled up by MICBIAS. When a micro-
phone is connected, VMIC is assumed to be between 0V
and 95% of VMICBIAS. If the jack is removed, VMIC increas-
es to VMICBIAS. This event causes JKMIC to be set, alert-
ing the system that the headset has been removed.
Alternatively, if the jack is inserted, VMIC decreases to
below 95% of VMICBIAS and JKMIC is cleared, alerting the
system that a jack has been inserted. The JKMIC bit can
be configured to create a hardware interrupt that alerts the
microcontroller of jack removal and insertion events.
Headphone Modes
The headphone amplifier supports differential, single-
ended, and capacitorless output modes, as shown in
Figure 8. In each mode, the amplifier can be configured
for stereo or mono operation. The differential and
capacitorless modes are inherently click and pop free.
The single-ended mode optionally includes click-and-
pop reduction to eliminate the click and pop that would
normally be caused by the output coupling capacitor.
When click-and-pop reduction is not required in the sin-
gle-ended configuration, leave LOUTN and ROUTN
unconnected.
GND
MIC
HPR
HPL
LOUTP
ROUTP
MICBIAS
JACKSNS/AUX
MICLP
LOUTN
Figure 7. Typical Configuration for Headset Detection
LOUTP
LOUTN
ROUTP
ROUTN
DIFFERENTIAL
LOUTP
LOUTN
ROUTP
ROUTN
CAPACITORLESS
1
F
LOUTP
220
F
LOUTN
SINGLE ENDED
1
F
ROUTP
220
F
ROUTN
OPTIONAL COMPONENTS REQUIRED FOR CLICK AND POP SUPPRESSION ONLY
Figure 8. Headphone Amplifier Modes
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9880AETM+ | IC CODEC AUDIO STEREO 48TQFN |
| MB86064PB-GE1 | DAC 14BIT 1GSA/S DUAL 12-EFBGA |
| MC100EL1648MELG | IC OSC VCO 1.1GHZ 14SOEIAJ |
| MC100EP195BMNG | IC DELAY LINE 1024TAP 32-QFN |
| MC100EP196BFAG | IC DELAY LINE 1024TAP 32-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9867EVKIT+ | 功能描述:音頻 IC 開發工具 MAX9867 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX9867EWV+ | 制造商:Maxim Integrated Products 功能描述:LOW-POWER, STEREO AUDIO CODEC - Rail/Tube |
| MAX9867EWV+T | 功能描述:接口—CODEC Stereo Audio CODEC for Portable Devices RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| MAX986ESA | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX986ESA+ | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。