參數資料
型號： MAX9702ETI+T
廠商： Maxim Integrated Products
文件頁數： 13/31頁
文件大?。?/td> 0K
描述： IC AMP AUDIO PWR 1.8W D 28TQFN
標準包裝： 2,500
系列： DirectDrive®
類型： D 類
輸出類型： 2-通道（立體聲）帶立體聲耳機
在某負載時最大輸出功率 x 通道數量： 1.8W x 2 @ 4 歐姆; 45mW x 2 @ 32 歐姆
電源電壓： 2.5 V ~ 5.5 V
特點： 消除爆音，差分輸入，I²C，靜音，短路和熱保護，關機
安裝類型： 表面貼裝
供應商設備封裝： 28-TQFN-EP（5x5）
封裝/外殼： 28-WFQFN 裸露焊盤
包裝： 帶卷 (TR)
MAX9702
Charge Pump
The MAX9702 features a low-noise charge pump. The
switching frequency of the charge pump is 1/2 the
switching frequency of the Class D amplifier. When
SYNC is driven externally, the charge pump switches at
1/2 fSYNC. When SYNC = VDD, the charge pump switch-
es with a spread-spectrum pattern. The nominal switch-
ing frequency is well beyond the audio range, and thus
does not interfere with the audio signals, resulting in an
SNR of 97dB. The switch drivers feature a controlled
switching speed that minimizes noise generated by
turn-on and turn-off transients. By limiting the switching
speed of the charge pump, the di/dt noise caused by
the parasitic bond wire and trace inductance is mini-
mized. Although not typically required, additional high-
frequency noise attenuation can be achieved by
increasing the size of C2 (see Typical Application
Circuit). The charge pump is active in both speaker and
headphone modes.
Input Multiplexer/Mixer
The MAX9702 features an input multiplexer/mixer that
allows three different audio sources to be selected and
mixed. Command register bits 5 and 6 select the input
channel (see Table 6), and the audio signal is output to
the active amplifier. When the mono path is selected
(bit 6 = 0, bit 5 = 1), the mono input is present on both
the outputs (with a gain according to Tables 4 and 5).
When the stereo path is selected, the left and right
inputs are present on the outputs (with a gain accord-
ing to Tables 4 and 5). When in mixer mode, the mono
input is added to each of the stereo inputs and present
at the output (with a gain according to Tables 4 and 5).
The mono and stereo signals are attenuated by 6dB
prior to mixing to maintain dynamic range. In mute,
none of input signals is present at output.
Headphone Sense Input (HPS)
The headphone sense input (HPS) monitors the head-
phone jack, and automatically configures the MAX9702
based on the voltage applied at HPS. A voltage of less
than 0.8V sets the MAX9702 to speaker mode. A volt-
age of greater than 2V disables the bridge amplifiers
and enables the headphone amplifiers.
For automatic headphone detection, connect HPS to
the control pin of a 3-wire headphone jack as shown in
Figure 8. With no headphone present, the output
impedance of the headphone amplifier pulls HPS to
less than 0.8V. When a headphone plug is inserted into
the jack, the control pin is disconnected from the tip
contact and HPS is pulled to VDD through the internal
600k
pullup resistor. When driving HPS from an exter-
nal logic source, drive HPS low when the MAX9702 is
shut down. Place a 10k
resistor in series with HPS and
the headphone jack to ensure ±8kV ESD protection.
Click-and-Pop Suppression
The MAX9702 features comprehensive click-and-pop
suppression that eliminates audible transients on start-
up and shutdown. While in shutdown, the H-bridge is
in a high-impedance state. During startup or power-up,
the input amplifiers are muted and an internal loop sets
the modulator bias voltages to the correct levels, pre-
venting clicks and pops when the H-bridge is subse-
quently enabled.
Current-Limit and Thermal Protection
The MAX9702 features current limiting and thermal pro-
tection to protect the device from short circuits and
overcurrent conditions. The headphone amplifier puls-
es in the event of an overcurrent condition. The speaker
amplifiers’ current-limiting protection clamps the output
current without shutting down the outputs. This can
result in a distorted output.
The MAX9702 has thermal protection that disables the
device into shutdown at +120°C until the temperature
decreases to +110°C.
1.8W, Filterless, Stereo, Class D Audio Power
Amplifier and DirectDrive Stereo Headphone Amplifier
20
______________________________________________________________________________________
MAX9702
100k
10k
10k
VDD
HPS
SDA
SHDN
SCL
HPL
I2
C
CONTROL
HPR
SHUTDOWN
CONTROL
Figure 8. HPS Configuration
相關PDF資料
PDF描述
MAX9704ETJ+ IC AMP AUDIO PWR 16W STER 32TQFN
MAX9705DEBC+T IC AMP AUDIO PWR 2.3W D 12UCSP
MAX9707ETX+T IC AMP AUDIO 2.3W STER+1 36TQFN
MAX9708ETN+TD IC AMP AUDIO PWR 42W STER 56TQFN
MAX9709ETN+TD IC AMP AUDIO PWR 50W STER 56TQFN
相關代理商/技術參數
參數描述
MAX9702EUI+ 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH/SPKR 2CH STEREO 1.8W/0.045W CLS-AB/CLS-D 28TSSO - Rail/Tube
MAX9702EUI+T 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH/SPKR 2CH STEREO 1.8W/0.045W CLS-AB/CLS-D 28TSSO - Tape and Reel
MAX9702EVCMODU 功能描述:放大器 IC 開發工具 MAX9702/2B Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX9702EVKIT 功能描述:放大器 IC 開發工具 MAX9702/2B Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX9703DEVBRD 功能描述:放大器 IC 開發工具 MAX9703 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*