- 您現在的位置：買賣IC網 > PDF目錄2091 > MAX9702ETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 1.8W D 28TQFN PDF資料下載
參數資料
| 型號： | MAX9702ETI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/31頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 1.8W D 28TQFN |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | D 類 |
| 輸出類型： | 2-通道（立體聲）帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 1.8W x 2 @ 4 歐姆; 45mW x 2 @ 32 歐姆 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，I²C，靜音，短路和熱保護，關機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Headphone Amplifier
In conventional single-supply headphone amplifiers,
the output-coupling capacitor is a major contributor of
audible clicks and pops. Upon startup, the amplifier
charges the coupling capacitor to its bias voltage, typi-
cally half the supply. Likewise, during shutdown the
capacitor is discharged to GND. This results in DC shift
across the capacitor, which in turn, appears as an
audible transient at the speaker. Since the MAX9702
headphone amplifier does not require output-coupling
capacitors, this does not arise.
The MAX9702 offers four headphone amplifier gain set-
tings controlled through the I2C interface. Headphone
amplifier gains of -2dB, +1dB, +4dB, and +7dB are set
by command register bits 3 and 4 (Table 5).
Additionally, the MAX9702 features extensive click-and-
pop suppression that eliminates any audible transient
sources internal to the device.
In most applications, the output of the preamplifier dri-
ving the MAX9702 has a DC bias of typically half the
supply. During startup, the input-coupling capacitor is
charged to the preamplifier’s DC bias voltage through
the RF of the MAX9702, resulting in a DC shift across
the capacitor and an audible click-and-pop. An internal
delay of 40ms eliminates the clicks-and-pops caused
by the input filter.
DirectDrive
Traditional single-supply headphone amplifiers have
outputs biased at a nominal DC voltage (typically half
the supply) for maximum dynamic range. Large-cou-
pling capacitors are needed to block this DC bias from
the headphone. Without these capacitors, a significant
amount of DC current flows to the headphone, resulting
in unnecessary power dissipation and possible dam-
age to both headphone and headphone amplifier.
Maxim’s DirectDrive architecture uses a charge pump
to create an internal negative supply voltage. This
allows the headphone outputs of the MAX9702 to be
biased at GND, almost doubling dynamic range while
operating from a single supply. With no DC component,
there is no need for the large DC-blocking capacitors.
Instead of two large (220F, typ) tantalum capacitors,
the MAX9702 charge pump requires two small ceramic
capacitors, conserving board space, reducing cost,
and improving the frequency response of the head-
phone amplifier. See the Output Power vs. Charge-
Pump Capacitance and Load Resistance graph in the
Typical Operating Characteristics for details of the pos-
sible capacitor sizes. There is a low DC voltage on the
driver outputs due to amplifier offset. However, the off-
set of the MAX9702 is typically 1.1mV, which, when
combined with a 32Ω load, results in less than 56A of
DC current flow to the headphones.
In addition to the cost and size disadvantages of the
DC-blocking capacitors required by conventional head-
phone amplifiers, these capacitors limit the amplifier’s
low-frequency response and can distort the audio sig-
nal. Previous attempts at eliminating the output-cou-
pling capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raises some issues:
1) The sleeve is typically grounded to the chassis.
Using the midrail biasing approach, the sleeve must
be isolated from system ground, complicating prod-
uct design.
2) During an ESD strike, the driver’s ESD structures
are the only path to system ground. Thus, the driver
must be able to withstand the full ESD strike.
3) When using the headphone jack as a line out to
other equipment, the bias voltage on the sleeve may
conflict with the ground potential from other equip-
ment, resulting in possible damage to the drivers.
MAX9702
1.8W, Filterless, Stereo, Class D Audio Power
Amplifier and DirectDrive Stereo Headphone Amplifier
______________________________________________________________________________________
19
VDD
+VDD
-VDD
VDD/2
GND
CONVENTIONAL AMPLIFIER BIASING SCHEME
DirectDrive BIASING SCHEME
Figure 7. Traditional Amplifier Output vs. MAX9702 DirectDrive
Output
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9704ETJ+ | IC AMP AUDIO PWR 16W STER 32TQFN |
| MAX9705DEBC+T | IC AMP AUDIO PWR 2.3W D 12UCSP |
| MAX9707ETX+T | IC AMP AUDIO 2.3W STER+1 36TQFN |
| MAX9708ETN+TD | IC AMP AUDIO PWR 42W STER 56TQFN |
| MAX9709ETN+TD | IC AMP AUDIO PWR 50W STER 56TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9702EUI+ | 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH/SPKR 2CH STEREO 1.8W/0.045W CLS-AB/CLS-D 28TSSO - Rail/Tube |
| MAX9702EUI+T | 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH/SPKR 2CH STEREO 1.8W/0.045W CLS-AB/CLS-D 28TSSO - Tape and Reel |
| MAX9702EVCMODU | 功能描述:放大器 IC 開發工具 MAX9702/2B Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9702EVKIT | 功能描述:放大器 IC 開發工具 MAX9702/2B Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9703DEVBRD | 功能描述:放大器 IC 開發工具 MAX9703 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。