- 您現在的位置：買賣IC網 > PDF目錄383443 > MAX5895 (Maxim Integrated Products, Inc.) 16-Bit, 500Msps Interpolating and Modulating Dual DAC with CMOS Inputs PDF資料下載
參數資料
| 型號： | MAX5895 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 16-Bit, 500Msps Interpolating and Modulating Dual DAC with CMOS Inputs |
| 中文描述： | 16位、500Msps、插值與調制、雙路DAC，CMOS輸入 |
| 文件頁數： | 29/32頁 |
| 文件大?。?/td> | 807K |
| 代理商： | MAX5895 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁
M
16-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
______________________________________________________________________________________
29
Power Supplies, Bypassing,
Decoupling, and Layout
Grounding and power-supply decoupling strongly influ-
ence the MAX5895 performance. Unwanted digital
crosstalk can couple through the input, reference,
power-supply, and ground connections, which can
affect dynamic specifications like signal-to-noise ratio
or spurious-free dynamic range. In addition, electro-
magnetic interference (EMI) can either couple into or
be generated by the MAX5895. Observe the grounding
and power-supply decoupling guidelines for high-
speed, high-frequency applications. Follow the power-
supply and filter configuration guidelines to achieve
optimum dynamic performance.
Using a multilayer printed circuit (PC) board with sepa-
rate ground and power-supply planes, run high-speed
signals on lines directly above the ground plane. Since
the MAX5895 has separate analog and digital sections,
the PC board should include separate analog and digi-
tal ground sections with only one point connecting the
three planes at the exposed paddle under the
MAX5895. Run digital signals above the digital ground
plane and analog/clock signals above the analog/clock
ground plane. Keep digital signals as far away from
sensitive analog inputs, reference lines, and clock
inputs as practical. Use a symmetric design of clock
input and the analog output lines to minimize 2nd-order
harmonic distortion components, thus optimizing the
dynamic performance of the DAC. Keep digital signal
paths short and run lengths matched to avoid propaga-
tion delay and data skew mismatches.
The MAX5895 requires five separate power-supply
inputs for the analog (AV
DD1.8
and AV
DD3.3
), digital
(DV
DD1.8
and DV
DD3.3
), and clock (AV
CLK
) circuitry.
Decouple each voltage supply pin with a separate
0.1μF capacitor as close to the device as possible and
with the shortest possible connection to the appropriate
ground plane. Minimize the analog and digital load
capacitances for optimized operation. Decouple all
power-supply voltages at the point they enter the PC
board with tantalum or electrolytic capacitors. Ferrite
beads with additional decoupling capacitors forming a
pi-network could also improve performance.
The exposed paddle (EP) MUST be soldered to the
ground.
Use multiple vias, an array of at least 4 x 4
vias, directly under the EP to provide a low thermal and
electrical impedance path for the IC.
Static Performance Parameter
Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from either a best straight-line fit
(closest approximation to the actual transfer curve) or a
line drawn between the end points of the transfer func-
tion, once offset and gain errors have been nullified.
For a DAC, the deviations are measured at every indi-
vidual step.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an
actual step height and the ideal value of 1 LSB. A DNL
error specification of less than 1 LSB guarantees no
missing codes and a monotonic transfer function.
Offset Error
The offset error is the difference between the ideal and
the actual offset current. For a DAC, the offset point is
the average value at the output for the two midscale
digital input codes with respect to the full-scale of the
DAC. This error affects all codes by the same amount.
Gain Error
A gain error is the difference between the ideal and the
actual full-scale output voltage on the transfer curve,
after nullifying the offset error. This error alters the slope
of the transfer function and corresponds to the same
percentage error in each step.
Dynamic Performance
Parameter Definitions
Settling Time
The settling time is the amount of time required from the
start of a transition until the DAC output settles its new
output value to within the specified accuracy.
Noise Spectral Density
The DAC output noise is the sum of the quantization
noise and thermal noise. Noise spectral density is the
noise power in 1Hz bandwidth, specified in dBFS/Hz.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog output (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
maximum SNR can be derived from the DAC’s resolu-
tion (N bits):
SNR
dB
= 6.02
dB
x N + 1.76
dB
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5895EGK | 16-Bit, 500Msps Interpolating and Modulating Dual DAC with CMOS Inputs |
| MAX5901ACEUT | Analog IC |
| MAX5927 | Low-Voltage. Quad. Hot-Swap Controllers/Power Sequencers |
| MAX5929 | Low-Voltage. Quad. Hot-Swap Controllers/Power Sequencers |
| MAX5930 | Low-Voltage. Triple. Hot-Swap Controllers/Power Sequencers/Voltage Trackers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5895EGK+D | 功能描述:數模轉換器- DAC 16-Bit 2Ch 500Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5895EGK+TD | 功能描述:數模轉換器- DAC 16-Bit 2Ch 500Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5895EGK-D | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5895EGK-TD | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5895EVCMOD2 | 功能描述:數模轉換器- DAC Evaluation Kit for the MAX5893/MAX5894/MAX5895 RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。