- 您現在的位置：買賣IC網 > PDF目錄2011 > MAX5725AAUP+T (Maxim Integrated Products)IC DAC 12BIT SRL 20TSSOP PDF資料下載
參數資料
| 型號： | MAX5725AAUP+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/35頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT SRL 20TSSOP |
| 標準包裝： | 2,500 |
| 設置時間： | 4.5µs |
| 位數： | 12 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 1.08W |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 8 電流，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
MAX5723/MAX5724/MAX5725
Ultra-Small, Octal-Channel, 8-/10-/12-Bit Buffered
Output DACs with Internal Reference and SPI Interface
24
Maxim Integrated
WDOG Command
The WDOG command (B[23:20] = 0001) updates the
watchdog timeout settings and safety levels for the
device. Timeout thresholds are selected in 1ms incre-
ments (1ms to 4095ms are available). The WD_MASK bit
can be used to mask the IRQ operation in response to the
watchdog status, if WD_MASK = 1, watchdog alarms will
not assert IRQ . The watchdog alarm status (WD bit) can
be polled using the available SPI status readback com-
mands regardless of WD_MASK settings. A write to this
register will not reset a previously triggered watchdog
alarm (use the WD_RESET command for this purpose).
The watchdog timer refresh and timeout behavior is
defined by the programmable safety level below.
Available safety levels (WL[1:0]):
Low (00): Watchdog timer will refresh with the execution
of any valid user mode command or no-op. Any success-
ful slave address acknowledge qualifies to restart the
watchdog timer (run to the ninth SCL edge), regardless
of the command which follows. Issuing hardware CLR or
LDAC falling edge will also refresh the watchdog timer.
A triggered watchdog alarm does not prevent writes to
any register. LDAC and CLR inputs still function after a
watchdog timeout event.
Medium (01): A WD_REFRESH command must be execut-
ed in order to refresh the watchdog timer. Other commands
as well as LDAC or CLR activity do not refresh the watch-
dog timer. A triggered watchdog alarm does not prevent
writes to any register. LDAC and CLR inputs still function
after a watchdog timeout event.
High (10): A WD_REFRESH command must be executed
to refresh the watchdog timer. Other commands as well
as LDAC or CLR activity do not refresh the watchdog
timer. A triggered watchdog alarm prevents execution
of all POWER, REF, CONFIG, DEFAULT, and RETURN
commands. LDAC and CLR inputs still function after a
watchdog timeout event.
Max (11): A WD_REFRESH command must be executed
to refresh the watchdog timer. Other commands, as well
as LDAC or CLR activity, do not refresh the watchdog
timer. A triggered watchdog alarm prevents execution of
all POWER, REF, CONFIG, DEFAULT, and RETURN com-
mands. LDAC and CLR are gated and do not function
after a watchdog timeout event.
Table 5. Watchdog Safety Level Protection
*Unless otherwise affected by Watchdog HOLD or CLR configurations as set by the CONFIG command. See the CONFIG register
definition for details.
Table 4. WDOG Command Format
WATCHDOG
SAFETY
LEVEL
ANY COMMAND
REFRESHES
WDT
CLR/LDAC
REFRESHES
WDT
SW_RESET
PLUS WD_RFRS
REFRESHES WDT
ALL REGISTERS
ACCESSIBLE AFTER
WDT TIMEOUT*
CLR/LDAC AFFECT
DAC REGISTERS
AFTER WDT TIMEOUT*
00 (Low)
X
01 (Med)
—
X
10 (High)
—
X
—
X
11 (Max)
—
X
—
B23 B22 B21 B20 B19 B18 B17 B16 B15 B14 B13 B12 B11 B10 B9
B8
B7 B6 B5 B4
B3
B2 B1
B0
0
1
X
C11 C10 C9
C8
C7
C6
C5
C4
C3 C2 C1 C0 WDM WL1 WL0 X
WDOG Command
Don’t Care
Timeout Selection
WD_MASK
WDOG
Safety
Level:
00: Low
01:
Med
10:
High
11: Max
Don’t
Care
Default Value
→
0
X
Command Byte
Data High Byte
Data Low Byte
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5735BUTN+ | IC DAC 16BIT 32CHAN SER 56-TQFN |
| MAX5741AUB+T | IC DAC 10BIT QUAD LP SER 10-UMAX |
| MAX5754UTN+ | IC DAC 14BIT 32CHAN SER 56-TQFN |
| MAX5774UCB+D | IC DAC 14BIT 32CHAN SER 64-TQFP |
| MAX5811PEUT+T | IC DAC SERIAL 10BIT 1CH SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5725AEVKIT# | 功能描述:數據轉換 IC 開發工具 MAX5725 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX5725AWP+T | 功能描述:數模轉換器- DAC 8Ch 12Bit Buffered Output DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5725BAUP+ | 功能描述:數模轉換器- DAC MAX5725BAUP+ RoHS:否 制造商:Maxim Integrated 轉換器數量: DAC 輸出端數量: 轉換速率: 分辨率: 接口類型: 穩定時間: 最大工作溫度: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| MAX5725BAUP+T | 制造商:Maxim Integrated Products 功能描述:ULTRA-SMALL, OCTAL-CHANNEL, 8-/10-/12-BIT BUFFERED OUTPUT DA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DAC 12BIT SPI/SRL 8CH 20TSSOP 制造商:Maxim Integrated Products 功能描述:Digital to Analog Converters - DAC MAX5725BAUP+T |
| MAX5725EVKIT# | 制造商:Maxim Integrated Products 功能描述:EV KIT FOR MAX5725 12B 8 CHANNEL DAC WITH SPI INTERFACE - Boxed Product (Development Kits) |
發布緊急采購，3分鐘左右您將得到回復。