- 您現在的位置：買賣IC網 > PDF目錄16180 > MAX1455EVKIT-NS (Maxim Integrated Products)EVAL KIT FOR MAX1455 PDF資料下載
參數資料
| 型號： | MAX1455EVKIT-NS |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 23/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL KIT FOR MAX1455 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | 接口，傳感器信號調節器 |
| 已用 IC / 零件： | MAX1455 |
| 已供物品： | 板 |
temperature indexed lookup table with one hundred
seventy-six 16-bit entries. The on-chip temperature sen-
sor provides a unique FSO trim from the table with an
indexing resolution approaching one 16-bit value every
1.5°C from -40°C to +125°C. The temperature indexing
boundaries are outside the specified absolute maximum
ratings. The minimum indexing value is 00hex, corre-
sponding to approximately -69°C. All temperatures below
this value output the coefficient value at index 00hex. The
maximum indexing value is AFhex, which is the highest
lookup table entry. All temperatures higher than approxi-
mately +184°C output the highest lookup table index
value. No indexing wraparound errors are produced.
Linear and Nonlinear Temperature
Compensation
Writing 16-bit calibration coefficients into the offset TC
and FSOTC registers compensates first-order tempera-
ture errors. The piezoresistive sensor is powered by a
current source resulting in a temperature-dependent
bridge voltage due to the sensor’s temperature coeffi-
cient resistance (TCR). The reference inputs of the off-
set TC DAC and FSOTC DAC are connected to the
bridge voltage. The DAC output voltages track the
bridge voltage as it varies with temperature, and by
varying the offset TC and FSOTC digital code and a
portion of the bridge voltage, which is temperature
dependent, is used to compensate the first-order tem-
perature errors.
The internal feedback resistors (RISRC and RSTC) for
FSO temperature compensation are set to 75k
.
To calculate the required offset TC and FSOTC com-
pensation coefficients, two test temperatures are need-
ed. After taking at least two measurements at each
temperature, calibration software (in a host computer)
calculates the correction coefficients and writes them to
the internal EEPROM.
With coefficients ranging from 0000hex to FFFFhex and
a +5V reference, each DAC has a resolution of 76V.
Two of the DACs (offset TC and FSOTC) utilize the sen-
sor bridge voltage as a reference. Since the sensor
bridge voltage is approximately set to +2.5V, the FSOTC
and offset TC exhibit a step size of less than 38V.
For high-accuracy applications (errors less than
0.25%), the first-order offset TC and FSOTC should be
compensated with the offset TC and FSOTC DACs, and
the residual higher order terms with the lookup table.
The offset and FSO compensation DACs provide
unique compensation values for approximately 1.5°C of
temperature change as the temperature indexes the
address pointer through the coefficient lookup table.
Changing the offset does not affect the FSO; however,
changing the FSO affects the offset due to the nature of
the bridge. The temperature is measured on both the
MAX1455 die and at the bridge sensor. It is recom-
mended to compensate the first-order temperature
errors using the bridge sensor temperature.
Typical Ratiometric
Operating Circuit
Ratiometric output configuration provides an output that is
proportional to the power-supply voltage. This output can
then be applied to a ratiometric ADC to produce a digital
value independent of supply voltage. Ratiometricity is an
important consideration for battery-operated instruments,
automotive, and some industrial applications.
The MAX1455 provides a high-performance ratiometric
output with a minimum number of external components
(Figure 2). These external components include the fol-
lowing:
One supply bypass capacitor
One optional output EMI suppression capacitor
Typical Nonratiometric
Operating Circuit
(5.5VDC < VPWR < 28VDC)
Nonratiometric output configuration enables the sensor
power to vary over a wide range. A low-dropout voltage
regulator, such as the MAX1615, is incorporated in the
circuit to provide a stable supply and reference for
MAX1455 operation. A typical example is shown in
Figure 3. Nonratiometric operation is valuable when
wide ranges of input voltage are to be expected and
the system A/D or readout device does not enable
ratiometric operation.
Internal Calibration Registers
The MAX1455 has five 16-bit internal calibration regis-
ters (ICRs) that are loaded from EEPROM, or loaded
from the serial digital interface.
Data can be loaded into the ICRs under three different
circumstances.
Normal Operation, Power-On Initialization Sequence:
The MAX1455 has been calibrated, the Secure-
Lock byte is set (CL[7:0] = FFhex), and UNLOCK is
low.
Power is applied to the device.
The power-on reset (POR) functions have been
completed.
Registers CONFIG, OTCDAC, and FSOTCDAC are
refreshed from EEPROM.
MAX1455
Low-Cost Automotive Sensor Signal
Conditioner
_______________________________________________________________________________________
7
相關PDF資料 |
PDF描述 |
|---|---|
| 382LX822M100N052 | CAP ALUM 8200UF 100V 20% SNAP |
| VI-J5P-EZ-F2 | CONVERTER MOD DC/DC 13.8V 25W |
| CMH322522-R68KL | INDUCTOR WIREWOUND .68UH 1210 |
| UPJ1V220MDD1TD | CAP ALUM 22UF 35V 20% RADIAL |
| EBC31DREF-S13 | CONN EDGECARD 62POS .100 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14562ETA+T | 功能描述:監控電路 OVP w/Voltage Clamp/Protection RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX14562EXT+T | 功能描述:監控電路 OVP w/Voltage Clamp/Protection RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX14566AEETA+ | 制造商:Maxim Integrated Products 功能描述:2ND GEN. USB DEVICE THAT COMBINES A USB HI-SPEED ANALOG SWI - Rail/Tube |
| MAX14566AEETA+T | 功能描述:模擬開關 IC USB HiSpeed an swtch w/USB host chrgr IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX14566BEETA+ | 制造商:Maxim Integrated Products 功能描述:SECOND GENERATION USB DEVICE THAT COMBINES A USB HI-SPEED AN - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。