參數資料
型號： MAX1441GUP/V+
廠商： Maxim Integrated Products
文件頁數： 32/41頁
文件大?。?/td> 0K
描述： IC PROXMITY SENSOR 2CH 20-TSSOP
其它有關文件： Automotive Product Guide
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 74
類型： 觸控式傳感器
輸入類型： 數字
輸出類型： 數字
接口： JTAG，串行
電流 - 電源： 100µA
安裝類型： 表面貼裝
封裝/外殼： 20-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 20-TSSOP
包裝： 管件
MAX1441
Automotive, Two-Channel Proximity and
Touch Sensor
38
I/O Ports
The device implements an I/O port that is slightly differ-
ent from those found in other MAXQ products.
The I/O port is still governed by the PI0, PO0, and PD0
registers.
When a PD0 register is cleared to 0, the port pin is oper-
ating as input and the pin is high impedance. The PI
register contains the input value. PI is read only. PI may
not always immediately equal PO due to capacitance at
the output.
When a PD0 bit is set to 1, the output is enabled and
the port pin output data corresponds to the PO value. In
addition, OUT1 and OUT2 can ONLY be used as open-
drain outputs. To use OUT1 and OUT2, clear PO bit to 0
and drive PD bit with inverted data.
When used as inputs, do not leave the port unconnect-
ed. Program unused port pins as outputs.
The external interrupt flag (EIF) is set to 1 when either a
rising or falling edge is detected on a port pin regardless
of its PD0 value. An interrupt is generated if it is enabled
(EIE = 1).
At power-up, weak pullups are enabled on pin P0.[4:0].
To disable a pullup, clear the associated bit in the PO0
register.
The external interrupts are asynchronous.
Peripheral Prioritization
In the discussion that follows, priority only has mean-
ing when two peripherals are both configured to drive
outputs at the same time. Then one of the named
peripheral’s output has priority over the other, thus
making the other’s output disabled. Note that the lower
priority peripheral can still be running and trying to
output value onto the pad. However, since it has lower
priority, its output is not driven onto the pad. For inputs,
all peripherals have equal priority—even though the
inputs may not be desirable. This means that if two input
peripherals sharing the same pin are enabled, both of
them receive the same input concurrently.
When a pin operates as input (whether it is a GPIO or
special-function input), its behavior is governed by PO0
and PD0. Anytime a pin behaves as an output (because
one of its special functions is configured as output), PO0
and PD0 are no longer used.
Port 0 supports the following functions: JTAG and GPIO.
All special functions have priority over GPIO.
JTAG Pin Special Function
The following apply when port pins are multiplexed with
the JTAG function:
The Special-Function Enable (SF Enable) signal for
these JTAG pins must be active during reset so
that the JTAG port is accessible during this time. SF
enable is controlled by the TAP register bit, which is
set to 1 on all resets.
TheSpecial-FunctionInput,whendisabled,shouldbe
gated high for TMS. This disables the JTAG interface
and forces the TAP into the Test-Logic-Reset state if
the TCK pin has been toggled for more than five times.
The TDO Special-Function Enable requires not only
that TAP = 1, but also that the TAP be in the Shift-IR or
Shift-DR state. The debug engine already produces a
control signal (TDONZ) to denote when the TAP is in
a shift state.
System Operating Modes
Following each system reset, the device automatically
activates the utility ROM at 8000h. The reset vector in
the utility ROM determines whether the program flow is to
start in the user mode or the ROM bootstrap mode. The
factor that determines which program is executed is the
System Programming Enable (SPE) bit in the ICDF reg-
ister. The SPE can be set/cleared with the debug mode
command using the TAP interface.
The device supports various modes of system opera-
tions. Normally, the device is running in user mode to
support user applications. The ROM bootstrap load-
er mode is used for initializing memory and system
configuration. The debug mode is intended to provide
real-time in-circuit debugging/emulation. The debug mode
is supported through a test access port (TAP) and the TAP
controller, which is compatible to the JTAG standard.
The TAP and the TAP controller are enabled after any
reset, but remain inactive until a valid command is
entered into the instruction register so as not to disrupt
normal user-mode operation. If the TAP is not used,
or the TAP interface pins are needed to serve another
purpose, the TAP can be disabled by clearing the TAP
enable (TAP) bit located in the SC system register.
Depending upon the mode desired, the instruction regis-
ter should be loaded with the associated "debug" or "in-
system programming" instruction. The method for loading
the instruction register is described in the subsequent
sections. These modes can be established anytime the
digital supply voltage is above the POR threshold (e.g.,
during system reset both are acceptable).
相關PDF資料
PDF描述
MAX14502AETL+T IC CARD READER USB-SD 40-TQFN
MAX14505EWC+T IC SWITCH DUAL SPDT 12WLP
MAX14523BATA/V+T IC CURRENT LIMIT SWITCH 8TDFN
MAX1452AAE+T IC SENSOR SIGNAL COND 16-SSOP
MAX14531EEWC+T IC USB SWITCH DP3T 12WLP
相關代理商/技術參數
參數描述
MAX1441IUP+ 功能描述:電容觸摸傳感器 RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
MAX1441IUP+T 功能描述:電容觸摸傳感器 RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
MAX1444EHJ 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1444EHJ/V+ 功能描述:模數轉換器 - ADC ANALOG TO DIGITAL CONVERTER RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1444EHJ/V+T 功能描述:模數轉換器 - ADC 10-Bit 40Msps 3.0V Low-Power ADC with Internal Reference RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*