- 您現在的位置：買賣IC網 > PDF目錄384648 > MAX108 (Maxim Integrated Products, Inc.) 【5V, 1.5Gsps, 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier PDF資料下載
參數資料
| 型號： | MAX108 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 【5V, 1.5Gsps, 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier |
| 中文描述： | ±5V、1.5Gsps、8位、超高速、ADC，帶有片上2.2GHz采樣/保持放大器 |
| 文件頁數： | 13/32頁 |
| 文件大?。?/td> | 428K |
| 代理商： | MAX108 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Principle of Operation
The MAX108’s flash or parallel architecture provides
the fastest multibit conversion of all common integrated
ADC designs. The key to this high-speed flash archi-
tecture is the use of an innovative, high-performance
comparator design. The flash converter and down-
stream logic translate the comparator outputs into a
parallel 8-bit output code and pass this binary code on
to the optional 8:16 demultiplexer, where primary and
auxiliary ports output PECL-compatible data at up to
750Msps per port (depending on how the demultiplex-
er section is set on the MAX108).
The ideal transfer function appears in Figure 2.
On-Chip Track/Hold Amplifier
As with all ADCs, if the input waveform is changing
rapidly during conversion, ENOB and signal-to-noise
ratio (SNR) specifications will degrade. The MAX108’s
on-chip, wide-bandwidth (2.2GHz) T/H amplifier
reduces this effect and increases the ENOB perfor-
mance significantly, allowing precise capture of fast
analog data at high conversion rates.
The T/H amplifier buffers the input signal and allows a
full-scale signal input range of ±250mV. The T/H ampli-
fier’s differential 50
input termination simplifies inter-
facing to the MAX108 with controlled impedance lines.
Figure 3 shows a simplified diagram of the T/H amplifier
stage internal to the MAX108.
Aperture width, delay, and jitter (or uncertainty) are
parameters that affect the dynamic performance of
high-speed converters. Aperture jitter, in particular,
directly influences SNR and limits the maximum slew
rate (dV/dt) that can be digitized without contributing
significant errors. The MAX108’s innovative T/H amplifier
design limits aperture jitter typically to less than 0.5ps.
Aperture Width
Aperture width (t
AW
) is the time the T/H circuit requires
(Figure 4) to disconnect the hold capacitor from the
input circuit (for instance, to turn off the sampling
bridge and put the T/H unit in hold mode).
Aperture Jitter
Aperture jitter (t
AJ
) is the sample-to-sample variation
(Figure 4) in the time between the samples.
Aperture Delay
Aperture delay (t
AD
) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 4).
Internal Reference
The MAX108 features an on-chip +2.5V precision
bandgap reference that can be used by connecting
M
±5V, 1.5Gsps, 8-Bit ADC with
On-Chip 2.2GHz Track/Hold Amplifier
______________________________________________________________________________________
13
(
0
+
(
255
255
254
129
128
127
126
3
2
1
0
ANALOG INPUT
OVERRANGE +
D
Figure 2. Transfer Function
TO
COMPARATORS
TO
COMPARATORS
BUFFER
AMPLIFIER
INPUT
AMPLIFIER
CLOCK
SPLITTER
ALL INPUTS ARE ESD PROTECTED
(NOT SHOWN IN THIS
SIMPLIFIED DRAWING).
SAMPLING
BRIDGE
GNDI
50
50
VIN+
VIN-
GNDI
C
HOLD
50
50
CLK+
CLK-
CLKCOM
Figure 3. Internal Structure of the 2.2GHz T/H Amplifier
HOLD
CLK
ANALOG
INPUT
SAMPLED
DATA (T/H)
T/H
t
AW
t
AD
t
AJ
TRACK
TRACK
APERTURE DELAY (t
AD
)
APERTURE WIDTH (t
AW
)
APERTURE JITTER (t
AJ
)
CLK
Figure 4. T/H Aperture Timing
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1090BEEI | 400ksps, +5V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface |
| MAX1090AEEI | 400ksps, +5V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface |
| MAX1090ACEI | RB Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 15V; Output Voltage (Vdc): 09V; Power: 1W; Low Cost 1W Converter; Power Sharing on Dual Output Version; Industry Standard Pinout; 1kVDC & 2kVDC Isolation Options; Optional Continuous Short Circuit Protected; UL94V-0 Package Material; Efficiency to 85% |
| MAX1090 | 400ksps, +5V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface |
| MAX1090BCEI | 400ksps, +5V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1080 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:300ksps/400ksps, Single-Supply, Low-Power, 8-Channel, Serial 10-Bit ADCs with Internal Reference |
| MAX1080ACUP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1080ACUP+ | 功能描述:模數轉換器 - ADC Low-Power 8-Ch 10-Bit w/Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1080ACUP+T | 功能描述:模數轉換器 - ADC Low-Power 8-Ch 10-Bit w/Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1080ACUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。