- 您現在的位置：買賣IC網 > PDF目錄383308 > MAS110S (Dynex Semiconductor Ltd.) Fast Turn-off Asymmetric Thyristor/Diode Module PDF資料下載
參數資料
| 型號： | MAS110S |
| 廠商： | Dynex Semiconductor Ltd. |
| 英文描述： | Fast Turn-off Asymmetric Thyristor/Diode Module |
| 中文描述： | 快速關斷不對稱晶閘管/二極管模塊 |
| 文件頁數： | 4/9頁 |
| 文件大小： | 67K |
| 代理商： | MAS110S |
MAS110S
4/9
THERMAL AND MECHANICAL DATA
Conditions
Min.
Max.
Units
Thermal resistance - junction to case
(Thyristor or diode)
R
th(j-c)
Symbol
Parameter
dc
o
C/W
0.21
-
Mounting force 6Nm
with mounting compound.
Thermal resistance - case to heatsink
(Thyristor or diode)
0.07
-
o
C/W
R
th(c-h)
125
o
C
T
vj
Virtual junction temperature
T
stg
Storage temperature range
V
isol
Isolation voltage
-
2.5
kV
-40
125
o
C
-40
-
-
125
o
C
-
T
op
Operating temperature range
Commoned terminals to base plate.
AC RMS, 1 min, 50Hz.
-
Mounting torque
-
6.0
Nm
ORDERING INFORMATION
The module type number is made up as follows:
MAS XXX S XX W
Nominal I
F(AV)
at T
case
= 75C
Single thyristor/diode configuration
Voltage grade. V
DRM
/100
Turn-off time code
Examples:
MAS 110 S 12 W
MAS 110 S 08 X
MODULE MOUNTING RECOMMENDATIONS
I
Adequate heatsinking is required to maintain the base
temperature at 75
o
C if full rated current is to be achieved. Power
dissipation may be calculated by use of V
and r
information
and loss curves in accordance with standard formulae. We can
provide assistance with calculations or choice of heatsink if required.
I
The heatsink surface must be smooth and flat; a surface finish
of N6 (32
μ
in) and a flatness within 0.05mm (0.002") are
recommended.
I
Immediately prior to mounting, the heatsink surface should be
lightly scrubbed with fine emery, Scotch Brite or a mild chemical
etchant and then cleaned with a solvent to remove oxide build up
and foreign material. Care should be taken to ensure no foreign
particles remain.
I
An even coating of thermal compound (eg. Unial) should be
applied to both the heatsink and module mounting surfaces. This
should ideally be 0.05mm (0.002") per surface to ensure optimum
thermal performance.
I
After application of thermal compound, place the module squarely
over the mounting holes, (or 'T' slots) in the heatsink. Using a
torque wrench, slowly tighten the recommended fixing bolts at
each end, rotating each in turn no more than 1/4 of a revolution at
a time. Continue until the required torque of 6Nm (55lb.ins) is
reached at both ends.
I
It is not acceptable to fully tighten one fixing bolt before starting
to tighten the others. Such action may DAMAGE the module.
Pressure contact asymmetric thyristor/diode module
相關PDF資料 |
PDF描述 |
|---|---|
| MAS281 | MIL-STD-1750A Microprocessor |
| MAX1002 | Low-Power, 60Msps, Dual, 6-Bit ADC |
| MAX1002CAX | Low-Power, 60Msps, Dual, 6-Bit ADC |
| MAX1003 | Low-Power, 90Msps, Dual 6-Bit ADC |
| MAX1003CAX | Low-Power, 90Msps, Dual 6-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAS1175 | 制造商:MAS 制造商全稱:MAS 功能描述:IC FOR 10.00 - 20.00 MHz VCTCXO |
| MAS1175A1SN06 | 制造商:MAS 制造商全稱:MAS 功能描述:IC FOR 10.00 - 20.00 MHz VCTCXO |
| MAS1175ASM1-T | 制造商:MAS 制造商全稱:MAS 功能描述:IC FOR 10.00 - 20.00 MHz VCTCXO |
| MAS1175ATB1 | 制造商:MAS 制造商全稱:MAS 功能描述:IC FOR 10.00 - 20.00 MHz VCTCXO |
| MAS1178 | 制造商:MAS 制造商全稱:MAS 功能描述:IC FOR 10.00 - 20.00 MHz VCXO |
發布緊急采購，3分鐘左右您將得到回復。