- 您現在的位置：買賣IC網 > PDF目錄98006 > M37735MHBXXXFP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37735MHBXXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, PLASTIC, QFP-80 |
| 文件頁數： | 10/90頁 |
| 文件大?。?/td> | 1575K |
| 代理商： | M37735MHBXXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
18
MITSUBISHI MICROCOMPUTERS
M37735MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
When bit 2 of the timer Ai mode register is “1”, the output is generated
from TAiOUT pin. The output is toggled each time the contents of the
counter reaches to 000016. When the contents of the count start flag
is “0”, “L” is output from TAiOUT pin.
When bit 2 is “0”, TAiOUT can be used as a normal port pin.
When bit 4 is “0”, TAiIN can be used as a normal port pin.
When bit 4 is “1”, counting is performed only while the input signal
from the TAiIN pin is “H” or “L” as shown in Figure 16. Therefore, this
can be used to measure the pulse width of the TAiIN input signal.
Whether to count while the input signal is “H” or while it is “L” is
determined by bit 3. If bit 3 is “1”, counting is performed while the
TAiIN pin input signal is “H” and if bit 3 is “0”, counting is performed
while it is “L”.
Note that the duration of “H” or “L” on the TAiIN pin must be two or
more cycles of the timer count sourse.
When data is written to the timer Ai register with timer Ai halted, the
same data is also written to the reload register and the counter. When
data is written to timer Ai which is busy, the data is written to the
reload register, but not to the counter. The counter is reloaded with
new data from the reload register at the next reload time. The contents
of the counter can be read at any time.
When the value set in the timer Ai register is n, the timer frequency
dividing ratio is 1/(n + 1).
Fig. 14 Timer Ai mode register bit configuration during timer mode
70
0 0 : Always “00” in timer mode
0
0 : No pulse output (TAiOUT is normal port pin)
1 : Pulse output
0 ! : No gate function (TAiIN is normal port pin)
1 0 : Count only while TAiIN input is “L”
1 1 : Count only while TAiIN input is “H”
62
3
4
51
00
0 : Always “0” in timer mode
Clock source selection bit
0 0 : Select f2
0 1 : Select f16
1 0 : Select f64
1 1 : Select f512
Timer A0 mode register
5616
Timer A1 mode register
5716
Timer A2 mode register
5816
Timer A3 mode register
5916
Timer A4 mode register
5A16
Addresses
相關PDF資料 |
PDF描述 |
|---|---|
| M37735MHLXXXHP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37736EHLXXXHP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP100 |
| M37736M4BXXXGP | 16-BIT, MROM, MICROCONTROLLER, PQFP100 |
| M37751M6C-XXXFP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37753M6C-XXXFP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37735MHL | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37735MHL-143HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37735MHLXXXHP |
| M37735MHLXXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37735S4BFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37735S4LHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。