參數資料
型號： M37735MHBXXXFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
封裝： 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80
文件頁數： 55/93頁
文件大?。?/td> 1802K
代理商： M37735MHBXXXFP
56
MITSUBISHI MICROCOMPUTERS
M37735MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
Fig. 63 Bit configuration of oscillation circuit control registers 0, 1
Fig. 64 How to write data in oscillation circuit control register 1
Writing data “8016” (LDM instruction)
Reset clock prescaler
Writing data “5516” (LDM instruction)
Writing data “0Y16” (LDM instruction)
CC2 to CC0 selection bits
How to reset clock prescaler
How to write in CC2 to CC0 selection bits
Note. “Y” is the sum of bits to be set. For example, when
setting bits 2 and 1 to “1”, “Y” becomes “6”.
Next instruction
Oscillation circuit control register 0
XCOUT drivability selection bit
0 : LOW
1 : HIGH
Main clock stop bit
0 : Main-clock oscillation is available.
1 : Main-clock oscillation is stopped.
System clock selection bit
Port-XC selection bit = “0” (Sub clock is not used.)
0 : Main clock is selected.
1 : Main clock divided by 8 is selected.
Port-XC selection bit = “1” (Sub clock is used.)
0 : Main clock is selected.
1 : Sub clock is selected.
Port-Xc selection bit
0 : Ports P77 and P76 are selected. (Sub clock is not used.)
1 : Pins XCIN and XCOUT are selected. (Sub clock is used.)
System clock stop bit at wait state
0 : Clocks f2 to f512 are operating at WIT state
1 : Clocks f2 to f512 stop at WIT state
Signal output disable selection bit (Refer to Table 7.)
Address
6C16
Note. Write to the oscillation circuit control
register 1 as the flow shown in Figure 64.
CM6 CM5 CM4 CM3 CM2
CM0
76543
2
1
0
Oscillation circuit control register 1
Main clock division selection bit
0 : Main clock is divided by 2.
1 : Main clock is not divided by 2.
Main clock external input selection bit
0 : Main-clock oscillation circuit is operating by itself.
Watchdog timer is used at returning from STP state.
1 : Main-clock is input externally.
Watchdog timer is not used at returning from STP state.
Sub clock external input selection bit
0 : Sub-clock oscillation circuit is operating by itself.
Port P76 functions as XCOUT pin.
Watchdog timer is used at returning from STP state.
1 : Sub-clock is input externally.
Port P76 functions as I/O port.
Watchdog timer is not used at returning from STP state.
0 : Always “0”
0 : Always “0” (However, writing data “5516” shown in Figure 64 is possible.)
Clock prescaler reset bit
Address
6F16
CC0
CC1
CC2
00
76543
2
1
0
相關PDF資料
PDF描述
M37735MHLXXXHP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M37735S4LHP 16-BIT, 12 MHz, MICROCONTROLLER, PQFP80
M37736EHBGS 16-BIT, UVPROM, 24 MHz, MICROCONTROLLER, CQCC100
M37736EHBXXXGP 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP100
M37736EHBGS 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC100
相關代理商/技術參數
參數描述
M37735MHL 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37735MHL-143HP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37735MHLXXXHP
M37735MHLXXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37735S4BFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER
M37735S4LHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*