參數資料
型號: M37548G3FP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
封裝: 4.40 X 6.50 MM, 0.65 MM PITCH, PLASTIC, LSSOP-20
文件頁數: 31/84頁
文件大?。?/td> 1427K
代理商: M37548G3FP
Rev.2.02
Mar 31, 2009
Page 37 of 81
REJ03B0210-0202
7548 Group
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O mode selection bit of the serial I/O control
register to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer, but
the two buffers have the same address in memory. Since the shift
register cannot be written to or read from directly, transmit data
is written to the transmit buffer register, and receive data is read
from the receive buffer register.
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
Fig 48. Block diagram of UART serial I/O
Fig 49. Operation of UART serial I/O function
1/4
OE
PE FE
1/16
Data bus
Receive buffer register
Address 001816
Receive shift register
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Baud rate generator
Frequency division ratio 1/(n+1)
Address 001C16
ST/SP/PA generator
Transmit buffer register
Transmit shift register
Address 001816
Transmit shift completion flag (TSC)
Transmit buffer empty flag (TBE)
Transmit interrupt request (TI)
Address 001916
ST detector
SP detector
UART control register
Address 001B16
Character length selection bit
Address 001A16
BRG count source selection bit
Transmit interrupt source selection bit
Serial I/O1 synchronous clock selection bit
Clock control circuit
Character length selection bit
7 bits
8 bits
Serial I/O1 status register
Serial I/O 1 control register
P06/SCLK
P04/RXD
P05/TXD
φSOURCE
TSC=0
TBE=1
RBF=0
TBE=0
RBF=1
TBE=1
TSC=1*
ST
D0
D1
SP
D0
D1
ST
SP
Transmit or receive clock
Transmit buffer
write signal
Serial output TXD
Receive buffer
read signal
Serial input RXD
* Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
Notes 1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1”, can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O1 control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1”.
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
ST
D0
D1
SP
D0
D1
ST
SP
相關PDF資料
PDF描述
M37548G1FP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
M37548G2-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
M37640E8-XXXFP 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP80
M37702S1ABFP 16-BIT, 16 MHz, MICROCONTROLLER, PQFP80
M37703E2BSP 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PDIP64
相關代理商/技術參數
參數描述
M37548G3FP#U0 功能描述:MCU 6K ROM 256K 20-SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C,Microwire,SPI,SSI,SSP,UART/USART,USB 外圍設備:欠壓檢測/復位,POR,WDT 輸入/輸出數:40 程序存儲器容量:96KB(96K x 8) 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
M37548G3-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37549G1FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37549G1-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37549G2FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER