參數資料
型號： M37510E6-XXXFP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP176
封裝： PLASTIC, QFP-176
文件頁數： 4/43頁
文件大?。?/td> 614K
代理商： M37510E6-XXXFP
12
7510 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Interrupt request
generating conditions
High
FFFD16
INTERRUPTS
A total of 15 sources can generate interrupts: 5 external, 9 inter-
nal, and 1 software.
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt
enable bit, and the interrupt disable flag except for the software in-
terrupt set by the BRK instruction. An interrupt is generated if the
corresponding interrupt request and enable bits are “1” and the in-
terrupt disable flag is “0”.
Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software.
The reset and BRK instruction can not be disabled with any flag or
bit.
The I flag disables all interrupts except for the BRK instruction in-
terrupt and the reset.
When several interrupts occur at the same time, the interrupts are
received according to priority.
Interrupt Operation
When an interrupt is received, the program counter and processor
status register are automatically pushed onto the stack. The inter-
rupt disable flag is set to inhibit other interrupts from interfering.
The corresponding interrupt request bit is cleared and the interrupt
jump destination address is read from the vector table into the pro-
gram counter.
Notes on Use
When the active edge of an external interrupt (INT0, INT1, CNTR0,
or CNTR1) is changed, the corresponding interrupt request bit
may also be set. Therefore, please take following sequence;
(1) Disable the external interrupt which is selected.
(2) Change the active edge selection.
(3) Clear interrupt request which is selected to “0”.
(4) Enable the external interrupt which is selected.
Table 1 Interrupt vector addresses and priority
Interrupt source
Priority
Low
FFFC16
Remarks
Reset (Note 2)
INT0
INT1
Non-maskable
External interrupt (active edge
selectable)
External interrupt (active edge
selectable)
Valid when serial I/O1 is se-
lected
Valid when serial I/O1 is se-
lected
Valid when serial I/O2 is se-
lected
Valid when serial I/O2 is se-
lected
External interrupt (active edge
selectable)
External interrupt (active edge
selectable)
External interrupt (valid when
an “L” level is applied)
Non-maskable software inter-
rupt
At BRK instruction execution
FFFA16
FFF816
FFF616
FFF416
FFF216
FFF016
FFEE16
FFEC16
FFEA16
FFE816
FFE616
FFE416
FFE216
FFE016
FFDC16
FFFB16
FFF916
FFF716
FFF516
FFF316
FFF116
FFEF16
FFED16
FFEB16
FFE916
FFE716
FFE516
FFE316
FFE116
FFDD16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Serial I/O1
reception
Serial I/O1
transmission
Timer X
Timer Y
Timer 2
Timer 3
Serial I/O2
reception
Serial I/O2
transmission
CNTR0
CNTR1
Timer 1
Key-on wake up
BRK instruction
Notes 1: Vector addresses contain interrupt jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
Vector addresses (Note 1)
At reset
At detection of either rising or
falling edge of INT0 input
At detection of either rising or
falling edge of INT1 input
At end of serial I/O1 data re-
ception
At end of serial I/O1 transfer
shift or when transmission
buffer is empty
At timer X underflow
At timer Y underflow
At timer 2 underflow
At timer 3 underflow
At end of serial I/O2 data re-
ception
At end of serial I/O2 transfer
shift or when transmission
buffer is empty
At detection of either rising or
falling edge of CNTR0 input
At detection of either rising or
falling edge of CNTR1 input
At timer 1 underflow
At falling of conjunction of in-
put logic level for port P2 (at
input)
相關PDF資料
PDF描述
M37516M6H-XXXKP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44
M37516M4H-XXXKP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44
M37516M6H-XXXKP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44
M37532E8FP 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO36
M37532M4-XXXGP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
M37510E7156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510E8156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M1156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M2156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37510M3156FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*