- 您現在的位置：買賣IC網 > PDF目錄299433 > M34C02-RMM1 (STMICROELECTRONICS) 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | M34C02-RMM1 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封裝： | 2 X 3 MM, VFDFPN-8 |
| 文件頁數： | 23/26頁 |
| 文件大?。?/td> | 388K |
| 代理商： | M34C02-RMM1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁
M34C02
6/26
Figure 6. Setting the Write Protection Register (WC = 0)
Setting the Software Write-Protection
The M34C02 has a hardware write-protection
feature, using the Write Control (WC) signal. This
signal can be driven High or Low, and must be
held constant for the whole instruction sequence.
When Write Control (WC) is held Low, the whole
memory array (addresses 00h to FFh) is write
protected. When Write Control (WC) is held High,
the write protection of the memory array is
dependent on whether software write-protection
has been set.
Software write-protection allows the bottom half of
the memory area (addresses 00h to 7Fh) to be
permanently
write
protected
irrespective
of
subsequent states of the Write Control (WC)
signal.
The write protection feature is activated by writing
once to the Protection Register. The Protection
Register is accessed with the device select code
set to 0110b (as shown in Table 2), and the E2, E1
and E0 bits set according to the states being
applied on the E2, E1 and E0 signals. As for any
other write command, Write Control (WC) needs to
be held Low. Address and data bytes must be sent
with this command, but their values are all ignored,
and are treated as Don’t Care. Once the
Protection Register has been written, the write
protection of the first 128 bytes of the memory is
enabled, and it is not possible to unprotect these
128 bytes, even if the device is powered off and
on, and regardless the state of Write Control (WC).
When the Protection Register has been written,
the M34C02 no longer responds to the device type
identifier 0110b in either read or write mode.
Figure 7. Result of Setting the Write Protection
START
SDA LINE
AI01935B
ACK
WORD
ADDRESS
VALUE
(DON'T CARE)
ACK
DATA
VALUE
(DON'T CARE)
STOP
ACK
CONTROL
BYTE
BUS ACTIVITY
MASTER
BUS ACTIVITY
Default EEPROM memory area
state before write access
to the Protect Register
AI01936C
Standard
Array
FFh
Standard
Array
80h
7Fh
00h
Standard
Array
FFh
Write
Protected
Array
80h
7Fh
00h
State of the EEPROM memory
area after write access
to the Protect Register
Memory
Area
相關PDF資料 |
PDF描述 |
|---|---|
| M368L1624DTM-LC4 | 16M X 64 DDR DRAM MODULE, 0.65 ns, DMA184 |
| M368L2923BUM-LC4 | 128M X 64 DDR DRAM MODULE, 0.65 ns, DMA184 |
| M368L2923DUN-CB3 | DDR SDRAM Unbuffered Module 184pin Unbuffered Module based on 512Mb D-die with 64/72-bit Non ECC/ECC 66 TSOP-II with Pb-Free (RoHS compliant) |
| M368L2923DUN-CCC | DDR SDRAM Unbuffered Module 184pin Unbuffered Module based on 512Mb D-die with 64/72-bit Non ECC/ECC 66 TSOP-II with Pb-Free (RoHS compliant) |
| M368L2923BUN-CB3 | Flash Memory IC; Memory Size:4Mbit; Supply Voltage Max:3V; Package/Case:48-FBGA; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes; Access Time, Tacc:90ns; Series:S29AL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34C02-RMN6T | 功能描述:電可擦除可編程只讀存儲器 5.5V 2K (256x8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M34C02-W | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Kbit Serial IC Bus EEPROM for DIMM serial presence detect |
| M34C02-WBN6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Kbit Serial IC Bus EEPROM For DIMM Serial Presence Detect |
| M34C02-WDW1G | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Kbit Serial IC Bus EEPROM for DIMM serial presence detect |
| M34C02-WDW1P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Kbit Serial IC Bus EEPROM for DIMM serial presence detect |
發布緊急采購，3分鐘左右您將得到回復。