參數資料
型號: M30201MX-XXXFP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
中文描述: 單片16位CMOS微機
文件頁數: 37/159頁
文件大小: 1496K
代理商: M30201MX-XXXFP
Unde
Interrupts
deeopmen
Mitsubishi microcomputers
M30201 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
37
Interrupt Sequence
An interrupt sequence — what are performed over a period from the instant an interrupt is accepted to the
instant the interrupt routine is executed — is described here.
If an interrupt occurs during execution of an instruction, the processor determines its priority when the
execution of the instruction is completed, and transfers control to the interrupt sequence from the next
cycle. If an interrupt occurs during execution of either the SMOVB, SMOVF, SSTR or RMPA instruction,
the processor temporarily suspends the instruction being executed, and transfers control to the interrupt
sequence.
In the interrupt sequence, the processor carries out the following in sequence given:
(1) CPU gets the interrupt information (the interrupt number and interrupt request level) by reading
address 00000
16
. After this, the corresponding interrupt request bit becomes "0".
(2) Saves the content of the flag register (FLG) as it was immediately before the start of interrupt
sequence in the temporary register (Note) within the CPU.
(3) Sets the interrupt enable flag (I flag), the debug flag (D flag), and the stack pointer select flag (U
flag) to “0” (the U flag, however, does not change if the INT instruction, in software interrupt
numbers 32 through 63, is executed).
(4) Saves the content of the temporary register (Note) within the CPU in the stack area.
(5) Saves the content of the program counter (PC) in the stack area.
(6) Sets the interrupt priority level of the accepted instruction in the IPL.
Interrupt Response Time
'Interrupt response time' is the period between the instant an interrupt occurs and the instant the first
instruction within the interrupt routine has been executed. This time comprises the period from the
occurrence of an interrupt to the completion of the instruction under execution at that moment (a) and the
time required for executing the interrupt sequence (b). Figure 1.25 shows the interrupt response time.
Instruction
Interrupt sequence
Instruction in
interrupt routine
Time
Interrupt response time
(a)
(b)
Interrupt request acknowledged
Interrupt request generated
(a) Time from interrupt request is generated to when the instruction then under execution is completed.
(b) Time in which the instruction sequence is executed.
Figure 1.25. Interrupt response time
After the interrupt sequence is completed, the processor resumes executing instructions from the first
address of the interrupt routine.
Note: This register cannot be utilized by the user.
相關PDF資料
PDF描述
M30220MA-XXXGP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30220MA-XXXRP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F4-XXXGP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F8-XXXGP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245FA-XXXGP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M30201MX-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201T-52SP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting Pod Probe M30201T-PRB to 52-pin 1.778mm-pitch SDIP (for M30201 Group)
M30201T-56FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter for Connecting Pod Probe M30201T-PRB to 56-pin 0.65mm-pitch QFP (for M30201 Group)
M30201T-PRB 制造商:Renesas Electronics Corporation 功能描述:POD PROBE FOR M16C/20 GROUP - Bulk
M3021-000002-017BG 功能描述:Pressure Sensor 246.56 PSI (1700 kPa) Vented Gauge Male - 1/4" (6.35mm) BSPP 0 mV ~ 100 mV (5V) Cylinder 制造商:te connectivity measurement specialties 系列:MSP300 零件狀態:有效 壓力類型:排氣式壓力計 工作壓力:246.56 PSI(1700 kPa) 輸出類型:模擬電壓 輸出:0 mV ~ 100 mV(5V) 精度:±1% 電壓 - 電源:5V 端口尺寸:公型 - 1/4"(6.35mm) BSPP 端口樣式:有螺紋 特性:溫度補償 端子類型:導線引線 最高壓力:493.13 PSI(3400 kPa) 工作溫度:-20°C ~ 85°C 封裝/外殼:圓柱型 供應商器件封裝:- 標準包裝:1