參數資料
型號: M30201F2-FP
元件分類: 微控制器/微處理器
英文描述: 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP56
封裝: PLASTIC, QFP-56
文件頁數: 11/158頁
文件大?。?/td> 1633K
代理商: M30201F2-FP
108
Under
development
Mitsubishi microcomputers
M30201 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Usage precaution
Timer B (timer mode, event counter mode)
(1) Reading the timer Bi register while a count is in progress allows reading , with arbitrary timing, the
value of the counter. Reading the timer Bi register with the reload timing gets “FFFF16”. Reading the
timer Bi register after setting a value in the timer Bi register with a count halted but before the counter
starts counting gets a proper value.
Timer B (pulse period/pulse width measurement mode)
(1) If changing the measurement mode select bit is set after a count is started, the timer Bi interrupt
request bit goes to “1”.
(2) When the first effective edge is input after a count is started, an indeterminate value is transferred to
the reload register. At this time, timer Bi interrupt request is not generated.
Timer X (timer mode)
(1) Reading the timer Xi register while a count is in progress allows reading, with arbitrary timing, the
value of the counter. Reading the timer Xi register with the reload timing gets “FFFF16”. Reading the
timer A0 register after setting a value in the timer Xi register with a count halted but before the counter
starts counting gets a proper value.
Timer X (event counter mode)
(1) Reading the timer Xi register while a count is in progress allows reading, with arbitrary timing, the
value of the counter. Reading the timer Xi register with the reload timing gets “FFFF16” by underflow
or “000016” by overflow. Reading the timer Xi register after setting a value in the timer Xi register with
a count halted but before the counter starts counting gets a proper value.
(2) When stop counting in free run type, set timer again.
Timer X (one-shot timer mode)
(1) Setting the count start flag to “0” while a count is in progress causes as follows:
The counter stops counting and a content of reload register is reloaded.
The TXiINOUT pin outputs “L” level.
The interrupt request generated and the timer Xi interrupt request bit goes to “1”.
(2) The timer Xi interrupt request bit goes to “1” if the timer's operation mode is set using any of the
following procedures:
Selecting one-shot timer mode after reset.
Changing operation mode from timer mode to one-shot timer mode.
Changing operation mode from event counter mode to one-shot timer mode.
Therefore, to use timer Xi interrupt (interrupt request bit), set timer Xi interrupt request bit to “0” after
the above listed changes have been made.
相關PDF資料
PDF描述
M30201M6T-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M4T-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M4-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M6T-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M4-XXXSP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP52
相關代理商/技術參數
參數描述
M30201F2T-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F2T-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F2-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F2-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F4T-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY