參數資料
型號： M30201F2-FP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP56
封裝： PLASTIC, QFP-56
文件頁數： 10/158頁
文件大?。?/td> 1633K
代理商： M30201F2-FP
107
Under
development
Mitsubishi microcomputers
M30201 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Usage precaution
Usage Precaution
Timer A (timer mode)
(1) Reading the timer A0 register while a count is in progress allows reading, with arbitrary timing, the
value of the counter. Reading the timer A0 register with the reload timing gets “FFFF16”. Reading
the timer A0 register after setting a value in the timer A0 register with a count halted but before the
counter starts counting gets a proper value.
Timer A (event counter mode)
(1) Reading the timer A0 register while a count is in progress allows reading, with arbitrary timing, the
value of the counter. Reading the timer A0 register with the reload timing gets “FFFF16” by under-
flow or “000016” by overflow. Reading the timer A0 register after setting a value in the timer A0
register with a count halted but before the counter starts counting gets a proper value.
(2) When stop counting in free run type, set timer again.
Timer A (one-shot timer mode)
(1) Setting the count start flag to “0” while a count is in progress causes as follows:
The counter stops counting and a content of reload register is reloaded.
The TA0OUT pin outputs “L” level.
The interrupt request generated and the timer A0 interrupt request bit goes to “1”.
(2) The timer A0 interrupt request bit goes to “1” if the timer's operation mode is set using any of the
following procedures:
Selecting one-shot timer mode after reset.
Changing operation mode from timer mode to one-shot timer mode.
Changing operation mode from event counter mode to one-shot timer mode.
Therefore, to use timer A0 interrupt (interrupt request bit), set timer A0 interrupt request bit to “0”
after the above listed changes have been made.
Timer A (pulse width modulation mode)
(1) The timer A0 interrupt request bit becomes “1” if setting operation mode of the timer in compliance
with any of the following procedures:
Selecting PWM mode after reset.
Changing operation mode from timer mode to PWM mode.
Changing operation mode from event counter mode to PWM mode.
Therefore, to use timer A0 interrupt (interrupt request bit), set timer A0 interrupt request bit to “0”
after the above listed changes have been made.
(2) Setting the count start flag to “0” while PWM pulses are being output causes the counter to stop
counting. If the TA0OUT pin is outputting an “H” level in this instance, the output level goes to “L”,
and the timer A0 interrupt request bit goes to “1”. If the TA0OUT pin is outputting an “L” level in this
instance, the level does not change, and the timer A0 interrupt request bit does not becomes “1”.
相關PDF資料
PDF描述
M30201M6T-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M4T-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M4-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M6T-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP56
M30201M4-XXXSP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP52
相關代理商/技術參數
參數描述
M30201F2T-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F2T-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F2-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F2-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30201F4T-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*