- 您現在的位置：買賣IC網 > PDF目錄382264 > M11B416256A-28J (Electronic Theatre Controls, Inc.) 256 K x 16 DRAM EDO PAGE MODE PDF資料下載
參數資料
| 型號： | M11B416256A-28J |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 256 K x 16 DRAM EDO PAGE MODE |
| 中文描述： | 256畝× 16的DRAM EDO公司頁面模式 |
| 文件頁數： | 6/15頁 |
| 文件大?。?/td> | 375K |
| 代理商： | M11B416256A-28J |
EliteMT
M11B416256A
Elite Memory Technology Inc
Publication Date
:
Feb. 2004
Revision
:
1.9
6/15
Notes :
1. Enables on-chip refresh and address counters.
2. V
IH
(min) and V
IL
(max) are reference levels for
measuring timing of input signals. Transition times
are measured between V
IH
and V
IL
.
3. In addition to meet the transition rate specification,
all input signals must transit between V
IH
and V
IL
in a
monotonic manner.
4. Assume that t
RCD
< t
RCD
(max). If t
RCD
is greater than
the maximum recommended value shown in this
table, t
RAC
will increase by the amount that t
RCD
exceeds the value shown.
5. Assume that t
RCD
≥
t
RCD
(max)
6. If
CAS
is low at the falling edge of
RAS
, data-out
will be maintained from the previous cycle. To initiate
a new cycle and clear the data-out buffer,
CAS
and
RAS
must be pulsed high.
7. Operation within the t
RCD
limit ensures that t
RCD
(max) can be met, t
RCD
(max) is specified as a
reference point only ; if t
RCD
is greater than the
specified t
RCD
(max) limit, access time is controlled
by t
CAC
.
8. Operation within the t
RAD
limit ensures that t
RAD
(max)
can be met. t
RAD
(max) is specified as a reference
point only ; if t
RAD
is greater than the specified t
RAD
(max) limit, access time is controlled by t
AA
.
9. Either t
RCH
or t
RRH
must be satisfied for a READ
cycle.
10.
t
OFF1
(max) defines the time at which the output
achieves the open circuit condition ; it is not a
reference to V
OH
or V
OL
.
11.
t
WCS
, t
RWD
, t
AWD
and t
CWD
are restrictive operating
parameters
in
READ-MODIFY-WRITE cycle only. If t
WCS
t
WCS(min)
, the cycle is an EARLY WRITE cycle and
the data output will remain an open circuit throughout
the entire cycle. If t
RWD
≥
t
RWD(min)
, t
AWD
≥
tAWD(min)
and t
CWD
≥
t
CWD(min)
, the cycle is READ-WRITE and
the data output will contain data read from the
selected cell. If neither of the above conditions is
met, the state of I/O (at access time and until
CAS
and
RAS
or
OE
go
LATE
WRITE
and
≥
back to V
IH
) is indeterminate.
OE
held high and
WE taken low after
CAS
goes low result in a LATE
WRITE (
OE
-controlled) cycle.
12. Those parameters are referenced to
CAS
leading
edge in EARLY WRITE cycles and WE leading edge
in LATE WRITE or READ-MODIFY- WRITE cycles.
13. During a READ cycle, if
OE
is low then taken HIGH
before
CAS
goes high, I/O goes open, if
OE
is tied
permanently
low,
a
READ-MODIFY-WRITE operation is not possible.
14. An initial pause of 200μs is required after power-up
followed by eight
RAS
refresh cycles (
RAS
only or
CBR) before proper device operation is assured. The
eight
RAS
cycle wake-ups should be repeated any
time the t
REF
refresh requirement is exceeded.
15. WRITE command is defined as WE going low.
16. LATE WRITE and READ-MODIFY-WRITE cycles must
have both tOFF2 and t
OEH
met (
OE
WRITE cycle) in order to ensure that the output
buffers will be open during the WRITE cycles.
17. The I/Os open during READ cycles once t
OFF1
or t
OFF2
occur.
18. Referenced to the earlier
CAS
falling edge.
19. Referenced to the latter
CAS
rising edge.
20. Output parameter (I/O) is referenced to corresponding
CAS
input, IO0~7 by
CASL
and IO8~15 by
CASH
.
21. Last falling
CAS
edge to first rising
CAS
edge.
22. Last rising
CAS
edge to next cycle’s last rising
CAS
edge.
23. Last rising
CAS
edge to first falling
CAS
edge.
24. Each
CAS
must meet minimum pulse width.
LATE
WRITE
or
high during
25. Referenced to the latter
CAS
falling edge.
26. All IOs controlled by
OE
, regardless
CASL
and
CASH
.
相關PDF資料 |
PDF描述 |
|---|---|
| M11B416256A-28T | 256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-30J | 256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-30T | 256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-35J | 256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-35T | 256 K x 16 DRAM EDO PAGE MODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M11B416256A-28T | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-30J | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-30T | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-35J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:256 K x 16 DRAM EDO PAGE MODE |
| M11B416256A-35T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:256 K x 16 DRAM EDO PAGE MODE |
發布緊急采購，3分鐘左右您將得到回復。