- 您現在的位置：買賣IC網 > PDF目錄44992 > LTC3616IUDD#TRPBF (LINEAR TECHNOLOGY CORP) 13.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 PDF資料下載
參數資料
| 型號： | LTC3616IUDD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 13.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| 封裝： | 3 X 5 MM, LEAD FREE, PLASTIC, QFN-24 |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 490K |
| 代理商： | LTC3616IUDD#TRPBF |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC3616
12
3616fa
operaTion
Burst Mode Operation—External Clamp
Connecting the MODE pin to a voltage in the range of
0.45V to 0.8V enables Burst Mode operation with exter-
nal clamp. During this mode of operation the minimum
voltage on the ITH pin is externally set by the voltage on
the MODE pin.
Pulse-Skipping Mode Operation
Pulse-skipping mode is similar to Burst Mode operation,
but the LTC3616 does not disable power to the internal
circuitry during sleep mode. This improves output voltage
ripple but uses more quiescent current, compromising
light load efficiency.
Tying the MODE pin to SVIN enables pulse-skipping mode.
As the load current decreases, the peak inductor current
will be determined by the voltage on the ITH pin until the
ITHvoltagedropsbelowthevoltagelevelcorrespondingto
0A. At this point, the peak inductor current is determined
by the minimum on-time of the current comparator. If the
load demand is less than the average of the minimum on-
time inductor current, switching cycles will be skipped to
keep the output voltage in regulation.
Forced Continuous Mode
In forced continuous mode the inductor current is con-
stantly cycled which creates a minimum output voltage
ripple at all output current levels.
Connecting the MODE pin to a voltage in the range of
1.1V to SVIN 0.58 will enable forced continuous mode
operation.
At light loads, forced continuous mode operation is less
efficient than Burst Mode or pulse-skipping operation, but
maybedesirableinsomeapplicationswhereitisnecessary
to keep switching harmonics out of the signal band.
Forced continuous mode must be used if the output is
required to sink current.
Dropout Operation
Astheinputsupplyvoltageapproachestheoutputvoltage,
the duty cycle increases toward the maximum on-time.
Further reduction of the supply voltage forces the main
switch to remain on for more than one cycle, eventually
reaching 100% duty cycle. The output voltage will then be
determined by the input voltage minus the voltage drop
across the internal P-channel MOSFET and the inductor.
Low Supply Operation
The LTC3616 is designed to operate down to an input
supply voltage of 2.25V. An important consideration at low
input supply voltages is that the RDS(ON) of the P-channel
and N-channel power switches increases. The user should
calculate the power dissipation when the LTC3616 is used
at 100% duty cycle with low input voltages to ensure that
thermal limits are not exceeded. See the Typical Perfor-
mance Characteristics graphs.
Short-Circuit Protection
The peak inductor current at which the current comparator
shuts off the top power switch is controlled by the voltage
on the ITH pin.
If the output current increases, the error amplifier raises
the ITH pin voltage until the average inductor current
matches the new load current. In normal operation the
LTC3616 clamps the maximum ITH pin voltage at ap-
proximately 1.05V which corresponds typically to 12A
peak inductor current.
When the output is shorted to ground, the inductor current
decays very slowly during a single switching cycle. The
LTC3616 uses two techniques to prevent current runaway
from occurring.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3617EUDD#PBF | 14 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3618EUF#TRPBF | 8 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3618IFE#PBF | 8 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO24 |
| LTC3618EFE#TRPBF | 8 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO24 |
| LTC3620EDC#PBF | SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3616MPUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3616MPUDD#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3617EUDD#PBF | 功能描述:IC REG SYNC 6A BUCK 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
| LTC3617EUDD#TRPBF | 功能描述:IC REG SYNC 6A BUCK 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC3617IUDD#PBF | 功能描述:IC REG SYNC 6A BUCK 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。