- 您現在的位置：買賣IC網 > PDF目錄385503 > LTC1404 (Linear Technology Corporation) Complete SO-8, 12-Bit, 600ksps ADC with Shutdown(SO-8封裝，12位,600ksps，模數轉換器（帶關斷）) PDF資料下載
參數資料
| 型號： | LTC1404 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Complete SO-8, 12-Bit, 600ksps ADC with Shutdown(SO-8封裝，12位,600ksps，模數轉換器（帶關斷）) |
| 中文描述： | 完整的SO - 8，12位，600ksps ADC的與關斷（以SO - 8封裝，12位，600ksps，模數轉換器（帶關斷）） |
| 文件頁數： | 12/24頁 |
| 文件大小： | 392K |
| 代理商： | LTC1404 |
12
LTC1404
APPLICATIO
S I
N
FOR
ATIO
U
If two pure sine waves of frequencies fa and fb are applied
to the ADC input, nonlinearities in the ADC transfer func-
tion can create distortion products at sum and difference
frequencies of mfa
±
nfb, where m and n = 0, 1, 2, 3, etc.
For example, the 2nd order IMD terms include (fa + fb) and
(fa – fb) while the 3rd order IMD terms includes (2fa + fb),
(2fa – fb), (fa + 2fb) and (fa – 2fb). If the two input sine
waves are equal in magnitude, the value (in decibels) of the
2nd order IMD products can be expressed by the following
formula.
20logAmplitude at (
W
U
IMD fa
fb
fa
fb
±
)
=
±
)
Amplitude at fa
Figure 5 shows the IMD performance at a 100kHz input.
Figure 5. Intermodulation Distortion Plot in Bipolar Mode
FREQUENCY (kHz)
0
40
80
100
140
180
20
60
120
160
220
200
240 260 280 300
A
1404 F05
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
f
= 600kHz
fa = 99.16992188kHz
fb = 102.6855469kHz
fa
fb
3fa
2fb – fa
2fa – fb
2fa + fb
2fa
3fb
fa + fb
2fb
2fb + fa
Peak Harmonic or Spurious Noise
The peak harmonic or spurious noise is the largest spec-
tral component excluding the input signal and DC. This
value is expressed in decibels relative to the RMS value of
a full-scale input signal.
Full Power and Full Linear Bandwidth
The full power bandwidth is the input frequency at which
the amplitude of the reconstructed fundamental is re-
duced by 3dB for a full-scale input signal.
The full linear bandwidth is the input frequency at which
the S/(N + D) has dropped to 68dB (11 effective bits). The
LTC1404 has been designed to optimize input bandwidth,
allowing the ADC to undersample input signals with fre-
quencies above the converter’s Nyquist Frequency. The
noise floor stays very low at high frequencies; S/(N + D)
becomes dominated by distortion at frequencies far be-
yond Nyquist.
Driving the Analog Input
The analog input of the LTC1404 is easy to drive. It draws
only one small current spike while charging the sample-
and-hold capacitor at the end of a conversion. During
conversion, the analog input draws only a small leakage
current. The only requirement is that the amplifier driving
the analog input must settle after the small current spike
before the next conversion starts. Any op amp that settles
in 160ns to small load current transient will allow maxi-
mum speed operation. If a slower op amp is used, more
settling time can be provided by increasing the time
between conversions. Suitable devices capable of driving
the ADC’s A
IN
input include the LT
1360 and the LT1363
op amps.
The LTC1404 comes with a built-in unipolar/bipolar detec-
tion circuit. If the V
SS
potential is forced below GND, the
internal circuitry will automatically switch to bipolar mode.
The following
list is a summary of the op amps that are
suitable for driving the LTC1404, more detailed informa-
tion is available in the Linear Technology databooks and
the LinearView
TM
CD-ROM.
LT1215/LT1216:
Dual and quad 23MHz, 50V/
μ
s single
supply op amps. Single 5V to
±
15V supplies, 6.6mA
specifications, 90ns settling to 0.5LSB.
LT1223:
100MHz video current feedback amplifier.
±
5V
to
±
15V supplies, 6mA supply current. Low distortion up
to and above 600kHz. Low noise. Good for AC applica-
tions.
LT1227:
140MHz video current feedback amplifier.
±
5V
to
±
15V supplies, 10mA supply current. Lowest distor-
tion at frequencies above 600kHz. Low noise. Best for AC
applications.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1405 | 12-Bit, 5Msps, Sampling ADC(12位, 5Msps,采樣模數轉換器) |
| LTC1406 | Low Power, 8-Bit, 20Msps, Sampling A/D Converter(低功耗,12位, 20Msps,采樣模數轉換器) |
| LTC1409 | 12-Bit, 800ksps Sampling A/D Converter with Shutdown(12位, 800ksps,采樣模數轉換器(帶關斷)) |
| LTC1412 | 12-Bit, 3Msps, Sampling A/D Converter |
| LTC1412C | 12-Bit, 3Msps, Sampling A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1404CS8 | 功能描述:IC A/D CONV 12BIT W/SHTDN 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1404CS8#PBF | 功能描述:IC A/D CONV 12BIT W/SHTDN 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1404CS8#TR | 功能描述:IC ADC 12BIT 600KSPS SHTDN 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1404CS8#TRPBF | 功能描述:IC A/D CONV 12BIT W/SHTDN 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1404CS8PBF | 制造商:Linear Technology 功能描述:ADC,LTC1404 12bit 600kSPS SOIC |
發布緊急采購，3分鐘左右您將得到回復。