參數資料
型號： LM9830
廠商： National Semiconductor Corporation
英文描述： LM9830 36-Bit Color Document Scanner
中文描述： LM9830 36位彩色文件掃描儀
文件頁數： 40/45頁
文件大?。?/td> 566K
代理商： LM9830
40
http://www.national.com
The correct Default Phase Difference (registers 52 and 53) must
be set for a scan to restart properly following a pause in the scan-
ning. See the LM9830 software for information on setting the
DPD register.
Attempting to read out the last pixels transferred into the SRAM
may cause the parallel port line buffer to underrun. Always make
sure there is at least 1K in buffer (register 01 >= 2) before reading
image data.
The number of fullsteps skipped at the start of a scan may be one
less than the Fullsteps to Skip at Start of Scan (registers 4A and
4B) setting.
The Scanning Step Size (registers 46 and 47) and Fast Feed
Step Size (registers 48 and 49) settings must be > 2.
When reverse is enabled, the LM9830 always stops on Red (line
rate color). When reverse is disabled, it will stop on any color.
The value in CR01 is reset by “start of scan reset” sos_reset.
sos_reset is asserted near the first line-end after a scan com-
mand is written (CR07=03). So if there is a residual value in
CR01, it will remain there for up to one line after a scan command
is written. CR07=08 (between scans) will reset CR01.
Some counters (register 01, notably), are not reset by the start of
a new scan until the first line has been scanned. For this reason
the chip should be briefly reset (register 07 = 08h) prior to a scan.
Make sure register 42 is set to the proper value (4 bit nibble or 8
bit bidirectional) for your PC’s parallel port mode before attempt-
ing to read data from the LM9830.
BUSY may go high by itself for the first few pixels after a scan is
started. After starting a scan, wait several ms before talking to the
LM9830.
When in 1 channel Mode A, the Dataport Target Color (reg03b1-
2) value is ignored for gamma reads and writes. The 1 Channel
Mode A Channel Color register (reg26b3-4) selects the gamma
table to be used when in 1 Channel Mode A. This only applies to
the gamma table. Register 3 is used to select the color for
gain/offset coefficient data.
Gamma and gain/offset coefficient data should be written with
register 7 = 0 (idle). Do not attempt to write gamma or gain/offset
coefficient data when scanning (register 7 = 3).
相關PDF資料
PDF描述
LM98503CCVV 10-Bit, 18 MSPS Camera Signal Processor
LM98503 10-Bit, 18 MSPS Camera Signal Processor
LM99CIMM 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface
LM99CIMMX 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface
LM9V381 Color STN-LCD Module
相關代理商/技術參數
參數描述
LM9830VJD 功能描述:視頻模擬/數字化轉換器集成電路 RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel
LM9830VJD/NOPB 功能描述:視頻模擬/數字化轉換器集成電路 RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel
LM9830VJDX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9830 36-Bit Color Document Scanner
LM9831 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9831 42-Bit Color, 1200dpi USB Image Scanner
LM9831CCVJD 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9831 42-Bit Color, 1200dpi USB Image Scanner
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*