- 您現在的位置：買賣IC網 > PDF目錄358878 > LM9830 (National Semiconductor Corporation) LM9830 36-Bit Color Document Scanner PDF資料下載
參數資料
| 型號： | LM9830 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | LM9830 36-Bit Color Document Scanner |
| 中文描述： | LM9830 36位彩色文件掃描儀 |
| 文件頁數： | 35/45頁 |
| 文件大小： | 566K |
| 代理商： | LM9830 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
35
http://www.national.com
feeding.
6.5 Returning to Transparency Mode with LM9830 Reset
The host can return the LM9830 to Transparency Mode and reset
the LM9830 by taking the INIT, AUTOFEED, SELECT_IN, and
STROBE pins low and then high again. Approximately 2 - 3
MCLKs after the rising edge of INIT, the LATCH pin will go high,
the TRISTATE pin will go low, and the LM9830 will tristate its D0-
D7 and control line outputs. This will reset the LM9830 as well as
make it transparent.
STROBE
6.6 Writing to the Configuration Register (Parallel Port)
The timing for writing to the LM9830 (sending data from the PC to
the LM9830) is shown in Figure 53. This is EPP timing, and it is
used for all parallel port Writes, even when in Nibble Mode (Nib-
ble Mode is only used to send data from the peripheral to the
host).
The write consists of two cycles, an address write cycle that tells
the LM9830 which address is going to be written to, and a data
write cycle that transmits the data to be stored in that address.
The handshaking is as follows:
The host takes STROBE low, indicating that the next operation
is a write.
The host puts data on D0-D7.
The host takes SELECT IN low to indicate that the data is valid.
The LM9830 latches the data and indicates that the data has
been latched by taking BUSY high.
The host responds and brings SELECT IN and STROBE high.
The LM9830 responds to the rising edge of SELECT IN by tak-
ing BUSY low.
This completes the address write cycle. The LM9830 is now pre-
pared for a byte write to the location contained in the address
byte. The handshaking for the data write is basically identical,
except AUTOFEED is used to latch the data instead of SELECT.
To write large quantities of data to a particular address, the
address only has to be written once. All data write operations will
write to the last address written. This is useful for writing DataPort
(register 06) data.
6.7 Reading From The Configuration Register (Parallel Port)
The procedure for reading the configuration register is different
for the EPP and Nibble Modes.
6.7.1 EPP Mode Configuration Register Read
An EPP read is shown in Figure 54. The handshaking for the
address write cycle of a read is identical to the address cycle for a
write. The data read cycle is as follows:
The host maintains STROBE high, indicating that the next oper-
ation is a read.
The host tristates D0-D7
The host takes AUTOFEED low to request data from the
LM9830.
The LM9830 places the data on the bus.
The LM9830 takes BUSY high to indicate the data is valid.
The host latches the data and responds by taking AUTOFEED
high.
The LM9830 tristates the bus.
The LM9830 takes BUSY low to indicate the cycle is complete
and it is ready for another cycle.
To read large quantities of data from a particular address, the
address only has to be written once. All data read operations will
read from the last address written. This is useful for reading pixel
(register 00) and DataPort (register 06) data.
6.7.2 Nibble Mode Configuration Register Read
This is not the traditional application of “Nibble Mode”, it is more
efficient and lower cost variation. The first half of the cycle is an
EPP address write, followed by a Nibble Mode read. Also, BUSY
is used for handshaking and ACK for a databit, eliminating the
problems caused by the hardware inversion of BUSY on the PC,
as well as allowing BUSY to perform roughly the same function it
does in EPP mode.
STROBE
AUTOFEED
INIT
Figure 51: LM9830 Transparent without Reset
SELECT IN
AUTOFEED
INIT
Figure 52: LM9830 Transparent with Reset
SELECT IN
STROBE
AUTOFEED
BUSY
Addr
D0 - D7
Figure 53: Writing to the Configuration Register
8-Bit Data
SELECT IN
8-Bit Data
STROBE
AUTOFEED
BUSY
Addr
D0 - D7
Figure 54: Reading from the Configuration Register (EPP)
SELECT IN
相關PDF資料 |
PDF描述 |
|---|---|
| LM98503CCVV | 10-Bit, 18 MSPS Camera Signal Processor |
| LM98503 | 10-Bit, 18 MSPS Camera Signal Processor |
| LM99CIMM | 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface |
| LM99CIMMX | 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface |
| LM9V381 | Color STN-LCD Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9830VJD | 功能描述:視頻模擬/數字化轉換器集成電路 RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| LM9830VJD/NOPB | 功能描述:視頻模擬/數字化轉換器集成電路 RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| LM9830VJDX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9830 36-Bit Color Document Scanner |
| LM9831 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9831 42-Bit Color, 1200dpi USB Image Scanner |
| LM9831CCVJD | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9831 42-Bit Color, 1200dpi USB Image Scanner |
發布緊急采購，3分鐘左右您將得到回復。