- 您現在的位置：買賣IC網 > PDF目錄358878 > LM9830 (National Semiconductor Corporation) LM9830 36-Bit Color Document Scanner PDF資料下載
參數資料
| 型號： | LM9830 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | LM9830 36-Bit Color Document Scanner |
| 中文描述： | LM9830 36位彩色文件掃描儀 |
| 文件頁數： | 37/45頁 |
| 文件大小： | 566K |
| 代理商： | LM9830 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
37
http://www.national.com
from the LM9830 in a continuous stream. First, write to register 3
to set what the data is (gamma or offset/gain) and what color
(red, green, or blue) the data is for. Then write to registers 4 and 5
to set the initial address (usually 0), and the R/W mode (R in this
case). To read data from the DataPort, the DataPort address (6)
needs to be inserted before every read to prefetch the data from
the external SRAM. The timing is shown in Figure 59. Note that
this applies onlyto offset and gain coefficient reads; the gamma
table may be read with or without the additional address writes.
The DataPort Address stored in registers 4 and 5 will be automat-
ically incremented after every read (if reading gamma data) or
every second read (if reading offset/gain coefficient words).
8.0 Scanning
8.1 Start Scanning - Initiating an Image Scan
An image scan is started by setting the Scanning bit in the Con-
figuration Register. The LM9830 will move the paper forward the
number of steps specified in the Stepper Motor Configuration reg-
ister and begin scanning. Scanning ends when the host writes a
new command to the command register (Idle, Paper Feed to Start
or Paper Feed to End) or when Paper Sensor #1 or Paper Sensor
#2 changes state (if programmed to do so).
The line buffer is reset when the Scanning bit is SET, not when it
is cleared. The host can continue to read stored data out of the
line buffer after a scan has stopped.
The LM9830 pixel data is read from configuration register
address 00. To read pixel data, the host should latch address 00
into the LM9830’s address pointer. Subsequent reads from the
host will read the next byte of pixel data stored in the line buffer.
Here are examples of two consecutive image data reads in the
three possible interface modes:
Image data can flow as fast as possible from the LM9830 to the
host, but can be interrupted at any time (by latching a different
address) to read the LM9830’s status registers, abort the scan,
etc.
If for some reason you want to pause the scan for some length of
time and resume later, do NOT reset the Scanning bits (return to
Idle). Simply stop reading pixel data. When the buffer fills up, the
LM9830 will automatically stop scanning and turn off power to the
stepper motor (when the delay goes beyond the time specified in
the
Hold Current Timeout
register).
The last byte of every line is the status byte (register 02). If the
line just transmitted was the beginning of a stepper motor pause
or reverse cycle, the
Pause
bit is set. For scanners unable to
reverse, this feature potentially allows the software to correct
images distorted by motor starting/stopping.
8.2 Reconstructing the Image Data Received By the PC
When reconstructing an image from the stream of data received
from the LM9830, it is useful to know the format of the data. The
LM9830 does not perform deinterleaving on the pixel data, it
comes out exactly as the sensor sends it. Deinterleaving and
other processing must be performed on the host PC.
For a single output CCD/CIS that outputs one line of data with
colors alternating at the line rate, the output format is:
R
1
, R
2
, R
3
, R
4
,..., R
n-2
, R
n-1
, R
n
(line m)
G
1
, G
2
, G
3
, G
4
,..., G
n-2
, G
n-1
, G
n
(line m + 1)
B
1
, B
2
, B
3
, B
4
,..., B
n-2
, B
n-1
, B
n
(line m + 2)
For a triple output CCD/CIS that outputs 3 lines of data (each x
pixels apart in the vertical direction) with colors alternating at the
Data
n
CS (INIT)
6
D0 - D7
Figure 59: Reading Gain and Offset Coefficients
through the DataPort (μP mode)
WR
(STROBE)
ALE
(SELECTIN)
RD
(AUTOFEED)
Data
n+1
6
6
Pixel n+1
STROBE
AUTOFEED
BUSY
Pixel n
D0 - D7
Figure 60: Reading Pixel Data (EPP)
SELECT IN
STROBE
AUTOFEED
BUSY
D0 - D7
Figure 61: Reading Pixel Data (Nibble Mode)
SELECT IN
ERROR (D0, D4)
SELECT (D1, D5)
PE (D2, D6)
ACK (D3, D7)
D7-D4
D3-D0
D7-D4
D3-D0
NIBBLE
CS (INIT)
RD (AUTO-
FEED)
Pixel n
D0 - D7
Figure 62: Reading Pixel Data (μP)
Pixel n+1
WR
(STROBE)
ALE
(SELECTIN)
相關PDF資料 |
PDF描述 |
|---|---|
| LM98503CCVV | 10-Bit, 18 MSPS Camera Signal Processor |
| LM98503 | 10-Bit, 18 MSPS Camera Signal Processor |
| LM99CIMM | 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface |
| LM99CIMMX | 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface |
| LM9V381 | Color STN-LCD Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9830VJD | 功能描述:視頻模擬/數字化轉換器集成電路 RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| LM9830VJD/NOPB | 功能描述:視頻模擬/數字化轉換器集成電路 RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| LM9830VJDX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9830 36-Bit Color Document Scanner |
| LM9831 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9831 42-Bit Color, 1200dpi USB Image Scanner |
| LM9831CCVJD | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9831 42-Bit Color, 1200dpi USB Image Scanner |
發布緊急采購，3分鐘左右您將得到回復。