- 您現在的位置：買賣IC網 > PDF目錄385490 > LM9627 (National Semiconductor Corporation) Metal Foil Resistor; Series:SMR1D; Resistance:2.5kohm; Resistance Tolerance:+/- 0.01 %; Power Rating:0.25W; Temperature Coefficient:+/-0.6 ppm; Terminal Type:PCB Surface Mount; Leaded Process Compatible:No PDF資料下載
參數資料
| 型號： | LM9627 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Metal Foil Resistor; Series:SMR1D; Resistance:2.5kohm; Resistance Tolerance:+/- 0.01 %; Power Rating:0.25W; Temperature Coefficient:+/-0.6 ppm; Terminal Type:PCB Surface Mount; Leaded Process Compatible:No |
| 中文描述： | 彩色CMOS圖像傳感器顯卡30醫科 |
| 文件頁數： | 18/37頁 |
| 文件大?。?/td> | 370K |
| 代理商： | LM9627 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Confidential
18
www.national.com
Functional Description
(continued)
11.0 OFFSET ADJUSTMENT
For maximum image quality over a wide range of light conditions
it is necessary to set an appropriate offset voltage before using
the sensor to capture images. This offset voltage must be
applied to the offset pin (38) of the sensor, and is used to adjust
the analogue video signal being fed to the internal A/D.
The level of the offset voltage determines the black level of the
image and has a direct impact on the image quality. Too high an
offset results in a white washed or hazy looking image, while too
low of an offset results in a dark image with low contrast even
though the light conditions are good.
A fine offset adjustment should be applied to each part by pro-
gramming the offset voltage via the I
2
C compatible serial inter-
face. To program an offset voltage the following procedure
should be followed:
The sensor’s
offset, fine_i
&
fine_ctrl
pins should be connected
as shown in figure 2.
The following procedure should be followed to calibrate the off-
set
Disable the black level compensation block by writing a logic
1 to bit 4 of the
Main Configuration Register 0
(MCFG0:
address 02Hex).
The offset can be adjusted by writing to the
Offset Compen-
sation Registers
(OCR: addresses 1F, 22 & 25 hex). Writing
00hex will give the largest voltage, while writing FF hex will
give the smallest value.
Run the following binary search algorithm
For n=7 to 0 step -1
{
Set bit n in the OCR registers (addresses 1F, 22 & 25
Hex) to a logic one by writing over the I
2
C compatible
interface.
Read a full frame and calculate the average black level
(BL
average
) of the first and last 5 black pixels in the every
row of the array
If (BL
average
< 100) then
Reset bit n in the OCR registers (addresses 1F, 22 &
25 Hex) to 0
else
Keep bit n set to one.
}
Enable the black level compensation block (if desired) by writ-
ing a logic 0 to bit 4 of the
Main Configuration Register 0
(MCFG0: address 02Hex).
12.0 OFFSET & GAIN
The fine offset adjustment and calibration method described in
section 11.0 will ensure that the sensor’s black level is optimized
for a fixed analog gain setting. However, when the analog gain is
changed substantially, the black level of the sensor will shift
resulting in a white washed image.
To stop this effect from occurring, the black level needs to be re-
calibrated. This can be done as part of the contrast adjustment
which is carried out by most digital image processors. If this is
not possible then the following method can be used.
The relationship between the gain and the offset can be
described with the following equation.
where:
Offset(G)
is the offset that needs to be programmed in
the OCR1, OCR2 & OCR3 registers to ensure
the correct black level setting for an analog
gain setting of
G
.
is the offset that needs to be programmed in
the OCR1, OCR2 & OCR3 registers to ensure
the correct black level setting for unity analog
gain, (
G
=0).
is a constant and will vary from sensor to sen-
sor
is the value programmed in the VGAIN regis-
ter of the sensor which determines the sen-
sor’s analog gain.
The following procedure should be used to calculate the value of
C
:
Use the calibration procedure described in section 11.0 to deter-
mine the offset at unity gain,
offset(0)
. Note the VGAIN register
should be set to 0.
Set the sensor’s analog gain register (VGAIN) to its max setting,
31, and repeat the calibration procedure described in section
11.0
.
This will allow the offset at full gain, 31, that needs to be
programmed in the OCR1, OCR2 & OCR3 registers to ensure
the correct black level setting to be determined.
The value of C for a particular sensor can be calculated using
the following formula:
Offset(0)
C
G
Once the value of C has been calculated, offset values for differ-
ent gain settings can be calculated using equation 1. It is recom-
mended that a two decimal point accuracy for C is maintained.
Offset(G) = Offset(
0
) + C * G
0.4
Offset(
31
) - Offset(
0
)
3.95
C
=
L
相關PDF資料 |
PDF描述 |
|---|---|
| LM98555 | CCD Driver |
| LM98555CCMH | CCD Driver |
| LM98714 | Three Channel, 16-Bit, 45 MSPS Digital Copier Analog Front End with Integrated CCD/CIS Sensor Timing Generator and LVDS Output |
| LMC6035IBP | Low Power 2.7V Single Supply CMOS Operational Amplifiers |
| LMC6035 | Low Power 2.7V Single Supply CMOS Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9627CCEA | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Color CMOS Image Sensor VGA 30 FPS |
| LM9627HEADBOARD | 功能描述:EVALUATION BOARD FOR LM9627 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| LM9628 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9628 Color CMOS Image Sensor VGA 30 FPS |
| LM9628EVAL-KIT | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9628 Color CMOS Image Sensor VGA 30 FPS |
| LM9628IEA | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9628 Color CMOS Image Sensor VGA 30 FPS |
發布緊急采購，3分鐘左右您將得到回復。