參數資料
型號: LM3101
廠商: National Semiconductor Corporation
英文描述: Secondary-Side PWM Controller
中文描述: 二次側PWM控制器
文件頁數: 7/20頁
文件大?。?/td> 319K
代理商: LM3101
Pin-by-Pin Description
(Continued)
Pin
Y
Symbol
Function
Description
11
POR
Power-On
Reset Flag
This open-collector output is driven low when either the supply voltage falls below the
Undervoltage Lockout Threshold Voltage or the output voltage is less than the Power-
on Reset Threshold Voltage. Leave the pin open if not used.
12
C
RD
Reset Delay Capacitor
Adding a capacitor between this pin and ground sets the power-on reset flag delay
time according to the following formula:
C
RD
e
T
DR
/60
#
10
3
Leave the pin open if not used. The POR flag will still operate if this function is not
used.
[
F, s,
X
]
.
13
FB
Feedback Input
A sample of the output voltage, via a resistor divider, is fed back into this pin, which is
the inverting input of the error amplifier.
14
EAO
Error Amplifier Output
Error Amplifier Output. The output can source 1.5 mA typically and sink 300
m
A
typically. This pin is primarily used for loop compensation.
Note:
Pins 1, 2, 4, 5, and 10 are internally clamped by a 5.6V zener diode. Do not force a voltage larger than 5V on these pins
without a resistor to limit the current to below 1 mA. All other pins are limited to the supply voltage.
Test Circuit
LM3101 specifications are measured using automated
test equipment. This circuit is provided for the custom-
er’s convenience when checking parameters. Due to
possible variations in testing conditions, the measured
values from these testing procedures may not match
those of the factory.
TL/H/11436–5
This test circuit is for exercising the LM3101 functions and
measuring its specifications. With the switch positions
shown, the supply current should measure 15 mA (typical)
for a supply voltage of 15V. Changing the supply voltage to
5V and opening SW6 on the V
OUT
pin should make the
supply current 11 mA (typical). Changing SW7 to the supply
voltage will shutdown the LM3101 output.
To test the oscillator section, adjust the 5 k
X
potentiometer
at the R
T
pin such that the oscillator frequency is approxi-
mately 500 kHz. Switch SW2 to obtain a 1 MHz frequency
(typical). The maximum duty cycle of 92% typically can also
be measured. Closing SW3 on pin R
SC
and putting SW7 (pin
FB) in the open position will change the oscillator frequency
to approximately 180 kHz.
Switching the MC pin, SW1, to ground and opening SW4,
the CMI pin, will put the device in current mode control. To
measure the current sense time delay (typically 75 ns),
close SW5 (connected to the CMI pin) and open SW6.
7
相關PDF資料
PDF描述
LM3102 SIMPLE SWITCHER㈢ Synchronous 1MHz 2.5A Step-Down Voltage Regulator
LM3102MHX SIMPLE SWITCHER㈢ Synchronous 1MHz 2.5A Step-Down Voltage Regulator
LM3102MH SIMPLE SWITCHER㈢ Synchronous 1MHz 2.5A Step-Down Voltage Regulator
LM3103 SIMPLE SWITCHER㈢ Synchronous 1MHz 0.75A Step-Down Voltage Regulator
LM3103MH SIMPLE SWITCHER㈢ Synchronous 1MHz 0.75A Step-Down Voltage Regulator
相關代理商/技術參數
參數描述
LM3101M 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Secondary-Side PWM Controller
LM3101N 制造商:Texas Instruments 功能描述:
LM3102 制造商:NSC 制造商全稱:National Semiconductor 功能描述:SIMPLE SWITCHER㈢ Synchronous 1MHz 2.5A Step-Down Voltage Regulator
LM3102EVAL 功能描述:BOARD EVALUATION LM3102 RoHS:否 類別:編程器,開發系統 >> 評估板 - DC/DC 與 AC/DC(離線)SMPS 系列:PowerWise®, SIMPLE SWITCHER® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC,步升 輸出及類型:1,非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
LM3102EVAL/NOPB 功能描述:電源管理IC開發工具 LM3102 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V