- 您現在的位置：買賣IC網 > PDF目錄30737 > LC85632 LED CLOCK, PDIP30 PDF資料下載
參數資料
| 型號： | LC85632 |
| 元件分類： | 時鐘及定時 |
| 英文描述： | LED CLOCK, PDIP30 |
| 封裝： | DIP-30 |
| 文件頁數： | 16/34頁 |
| 文件大?。?/td> | 394K |
| 代理商： | LC85632 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
The conditions concerning alarm output are as follows:
— In principle, the later occurring alarm is given priority.
Example: The alarms will operate as follows if alarm A is set for 12:02 and alarm B is set for 12:04.
Alarm A begins to operate at 12:02
At 12:04 alarm B begins to operate. At the same time alarm A stops.
Figure 14 Alarm Operation Priority
Exceptions to later arrival priority: Although in principle the later occurring alarm take priority, in the
following case alarm A takes priority and alarm B does not operate.
Assume that the alarm A set time is 12:30 and the alarm B set time is 12:00 and the alarms are enabled at
12:15.
Now, time progress and 12:30 arrives and alarm B operates. At this point, while the current time is still 12:30,
alarm B will not operate even if the alarm B set time is advanced to 12:30. Here, alarm A will take priority and
alarm B will not operate.
— If both alarms are set to the same time, alarm A takes priority and alarm B does not operate.
— If the other alarm operates during a snooze interruption of one alarm, the interrupted alarm is stopped.
Example: Assume alarm A has been interrupted by the snooze function and alarm B operates. At this
point only the ALM-B OUTPUT pin outputs an alarm signal, and no signal is output from the
ALM-A OUTPUT pin when the snooze period for alarm A completes.
(8) Other points
Notes on the alarm indicators (ALM INDICATOR)
This output is used to display the alarm state on the LED display. Its display states are as follows.
— Normal operation (No alarm times set and no operations enabled) : Off
— Normal operation (Alarm time set and alarm enabled)
: On
— Alarm setting mode
: Flashing (1 Hz)
— Initial state flashing mode
: Lit (not flashing)
— Flashing mode following a power loss
: Lit (not flashing)
Figure 15 Alarm Indicators
Radio output
If the radio output is in the on state, i.e., the RADIO OUTPUT pin is high, and either alarm A or alarm B output
goes on, the radio output will go off, i.e., the RADIO OUTPUT pin will go low.
LC85632
No. 4659-23/34
相關PDF資料 |
PDF描述 |
|---|---|
| LC8650T | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC8900KQ | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC8901 | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
| LC8901Q | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC8902 | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC85A | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:TRANSIENT ABSORPTION ZENER |
| LC86104 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC86104A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:168bytes RAM 8-BIT SINGLE CHIP MICROCOMPUTER |
| LC86104C | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:On-chip 168 Bytes RAM 8-BIT SINGLE CHIP MICROCOMPUTER |
| LC86108 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。