- 您現在的位置：買賣IC網 > PDF目錄30737 > LC85632 LED CLOCK, PDIP30 PDF資料下載
參數資料
| 型號： | LC85632 |
| 元件分類： | 時鐘及定時 |
| 英文描述： | LED CLOCK, PDIP30 |
| 封裝： | DIP-30 |
| 文件頁數： | 11/34頁 |
| 文件大?。?/td> | 394K |
| 代理商： | LC85632 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Operation
Clearing the Initial Reset State
In the initial state when power is first applied, the display reads 12:00 (or 0:00 for 24 hour display) and the numbers and
the colon flash alternately. This is called the “initial reset state”. The period of the flashing is 1 Hz.
To clear the flashing state, apply a high or low level to the TIME SET INPUT pin when the colon is lit.
Figure 11 Clearing the Initial Input State Flashing
In figure 11, the shaded areas under the LED display line are times when the numbers are lit. At these times the colon
will be off.
Here, the application of an input to the TIME SET INPUT input x in the figure when the numbers are lit, i.e., the timing
indicated by “A”, will be invalid. Since the colon is off at that point, the flashing state will not be cleared. However, such
an input is valid at a point when the numbers are off, i.e., the timing indicated by “B”. Since the colon will be lit in this
state, the flashing state will be cleared and the clock will enter normal display mode.
Alternatively, an input signal such as the TIME SET INPUT input y in the figure can be applied. Here, the low (or high)
level is held until the flashing is cleared at the timing indicated by “D” in the figure.
When the flashing state is cleared, the colon also will stop flashing, and remain lit.
LC85632
No. 4659-19/34
相關PDF資料 |
PDF描述 |
|---|---|
| LC8650T | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC8900KQ | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC8901 | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
| LC8901Q | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC8902 | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC85A | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:TRANSIENT ABSORPTION ZENER |
| LC86104 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC86104A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:168bytes RAM 8-BIT SINGLE CHIP MICROCOMPUTER |
| LC86104C | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:On-chip 168 Bytes RAM 8-BIT SINGLE CHIP MICROCOMPUTER |
| LC86108 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。