- 您現在的位置：買賣IC網 > PDF目錄43900 > L6460TR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | L6460TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64 |
| 文件頁數： | 81/139頁 |
| 文件大?。?/td> | 3837K |
| 代理商： | L6460TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
Power saving modes
L6460
46/139
Doc ID 17713 Rev 1
10.2
Hibernate mode
L6460’s hibernate mode allows the firmware to switch off some (or all) selected System
Regulators leaving in on state only those necessary to resume L6460 to operative condition
when waked-up by an external signal.
Hibernate mode is selected when the firmware writes the command word in the
HibernateCmd register. When in hibernate mode L6460 will force regulators in the state
(on/off) selected by the firmware by writing in the HibernateCmd register and will force
nRESET pin low.
The exiting from hibernate mode is achieved by forcing at low level nAWAKE pin (or GPIO5
pin if L6460 is in Slave mode); L6460 will also exit from hibernate mode if an undervoltage
event happens on VSupply, VSupplyInt, VPump or V3v3.
When the exit from hibernate mode is due to an external command, L6460 sets to ‘1’ the bit
HibModeLth in the HibernateStatus register.
10.3
Low power mode
When in normal operating mode, the microcontroller can place L6460 in “Low Power mode”.
In this condition L6460 sets all bridges outputs in high impedance, powers down all
regulators (including system regulators and charge pump) and disables almost all its circuits
including internal clock reducing as much as possible power consumption.
The only circuits that remain active are:
–V3V3 internal regulator.
–
nAWAKE pin current pull-up.
–
nRESET pin that will be pulled low.
–
POR circuit.
The entering in low power mode is obtained in different ways depending if L6460 is
configured as slave device or not. When L6460 is configured as slave device the low power
mode is directly controlled by nAWAKE pin that acts as an enable: if this pin is low for a time
longer then tAWAKEFILT, Low Power mode is entered; if this pin is high L6460 exits from Low
Power mode.
In all other start-up configurations, Low Power mode is entered by writing a Low Power
mode command in the PowerModeControl register; once L6460 is in Low Power mode it
starts checking the nAWAKE pin status: if it is found low for a time longer than tAWAKEFILT,
L6460 exits from Low Power mode and restarts its startup sequence. When the nAWAKE
pin is externally pulled low, the “AWAKE” event is stored and it is readable through SPI.
L6460 will also exit from Low Power mode if a POR event is found.
Note:
When in “Low power mode” VSupply is monitored only for its power on reset level.
10.4
nAWAKE pin
At the start up, before L6460 has identified the required operation mode (see Chapter 8), a
current sink IINP is always active to pull down nAWAKE pin. As soon as the operation mode
(basic, slave, master or single device) is detected, the functionality of nAWAKE pin will be
different.
相關PDF資料 |
PDF描述 |
|---|---|
| L6515 | BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44 |
| L6560AD | 0.7 A POWER FACTOR CONTROLLER, PDSO8 |
| L6560AD013TR | 0.7 A POWER FACTOR CONTROLLER, PDSO8 |
| L6560D013TR | 0.7 A POWER FACTOR CONTROLLER, PDSO8 |
| L6562ATN | SWITCHING CONTROLLER, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6470 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI |
| L64702QC-33 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L64704 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:L64704 Satellite Decoder technical manual 5/97 |
| L6470H | 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6470HTR | 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。