參數資料
型號： L6460TR
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, PQFP64
封裝： 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件頁數： 76/139頁
文件大小： 3837K
代理商： L6460TR
L6460
Start-up configurations
Doc ID 17713 Rev 1
41/139
8.3
Slave device mode
In slave device mode, L6460 consider the nAWAKE pin as an input enable. Since this is now
a digital pin, the current pull up source inside the nAWAKE circuit is disabled.
At the startup, if the nAWAKE pin is found to be low for a period higher than tAWAKEFILT,
L6460 enters directly in the “Low Power mode”; when nAWAKE pin is pulled high for a
period higher than tAWAKEFILT, L6460 begins its start up procedure.
8.4
Master device mode
In master device mode, L6460 begins its start up procedure without waiting for any external
enable signal and it uses GPIO[5] pin to drive the nAWAKE pin of Slave devices.
During the whole start up time, it forces its GPIO[5] pin at logic level “0” in order to maintain
all slave devices in “Low Power mode” as previously described. When start up operations
are completed, L6460 forces the GPIO[5] output to logic level “1” to enable the slave devices
and keeps GPIO[5] output at high level until it senses an under-voltage on any of its System
regulators. If firmware writes in the PwrCtrl register to set Master L6460 in “Low Power
mode” it immediately forces GPIO[5] output to logic level “0” to force the slave devices to
enter in “Low Power mode”, then it waits for TMASTWAIT time and it starts its “Low Power
mode” sequence.
8.5
Single device mode
In single device mode, the device behaves similarly to master device mode but:
1.
It doesn’t use the GPIO[5] pin to drive slave devices.
2.
It doesn’t wait for TMASTWAIT before entering in “Low Power mode”.
8.6
Sub-configurations for slave, master or single device modes
Each slave, master or single device modes can be divided in other minor modes depending
on the start-up sequence needed for L6460 internal regulators.
Unless otherwise specified, in all the following modes the regulators included in the start up
sequence are considered system regulators and they start in the sequence indicated.
8.6.1
Bridge mode
In this configuration bridges 3 and 4 are not used as regulators and therefore can be
configured by the firmware in any of their possible bridge modes.
When in this mode the power-up sequence is:
1.
Main switching regulator (VSWmain).
2.
Main linear regulator (VLINmain).
相關PDF資料
PDF描述
L6515 BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44
L6560AD 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560AD013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560D013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6562ATN SWITCHING CONTROLLER, PDIP8
相關代理商/技術參數
參數描述
L6470 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI
L64702QC-33 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
L64704 制造商:未知廠家 制造商全稱:未知廠家 功能描述:L64704 Satellite Decoder technical manual 5/97
L6470H 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L6470HTR 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*