參數資料
型號： L6460TR
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, PQFP64
封裝： 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件頁數： 114/139頁
文件大小： 3837K
代理商： L6460TR
Power bridges
L6460
76/139
Doc ID 17713 Rev 1
14.1.8
Battery charger or switching regulator (Bridge 4)
The functionality of this circuit is obtained by using the bridge 4 output stage. This circuit is
powered directly from VSupply and it is intended to be used as a battery charger or a
switching regulator.
The control loop block diagram is shown in the Figure 21.
Figure 21.
Battery charger control loop block diagram
The battery charger control loop implements an asynchronous switching regulator intended
to be used as a constant voltage/constant current programmable source.
When used as a simple switching regulator, it could be a system regulator depending on
startup configurations
When a system regulator under-voltage event is detected L6460 will enter in reset state
signaling this event to the microcontroller by pulling low the nRESET pin and disabling most
of its internal blocks.
When the control loop is intended to be used as a battery charger, the Aux3BatteryCharge
bit must be written in the Aux3SwCfg1 register. This is because in this case the
undervoltage event that will be sure present when charging a battery (see battery charger
profile in Figure 22) will not be considered during start up sequence.
The regulated output voltage will be externally set by a resistor divider network connected to
VREF_FB pin. L6460 has the possibility to choose between four voltage references (and, as a
consequence, four under-voltage thresholds) using the serial interface. The feedback
reference voltage selection is made by writing the SelFBRef[1:0] bits in the Aux3SwCfg1
register.
The regulation of the output current can be done externally, by using a sense resistor
connected in series on the path that provides current to the load. By using an external
differential amplifier the customer can set the desired V = f(I) characteristic, and therefore
IREF_FB
VREF_FB
COMP_I
COMP_V
PULSE SKIPPING
BURST
CONTROL LOGIC
PEAK CURRENT
MODE CONTROL
LOGIC
BRIDGE 4
PARALLELED
POWER
STAGE
SelFBRef<1:0>
DC4_plus
DC4_minus
SelCurrRef<1:0>
DIFF
AMPLI
TO
LOAD
FBRef
CurrRef
Ilimit
PWM
L6460
相關PDF資料
PDF描述
L6515 BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44
L6560AD 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560AD013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560D013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6562ATN SWITCHING CONTROLLER, PDIP8
相關代理商/技術參數
參數描述
L6470 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI
L64702QC-33 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
L64704 制造商:未知廠家 制造商全稱:未知廠家 功能描述:L64704 Satellite Decoder technical manual 5/97
L6470H 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L6470HTR 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*