- 您現在的位置：買賣IC網 > PDF目錄43899 > L5993 (STMICROELECTRONICS) 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDIP16 PDF資料下載
參數資料
| 型號： | L5993 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封裝： | DIP-16 |
| 文件頁數： | 21/22頁 |
| 文件大?。?/td> | 200K |
| 代理商： | L5993 |
CONSTANT POWER FUNCTION
Pulse-by-pulse current limitation prevents peak
primary current from exceeding a given level.
This, in turn, limits the maximum power deliver-
able to the output or, in other words, the power
capability of a converter. The capability, however,
depends on switching frequency: for example, in
a discontinuous current mode flyback they are just
proportional.
In SMPS’ of raster-scanned CRT displays the
switching frequency is usually synchronized to the
raster line scan signal of the display in order to in-
crease noise immunity. More and more often,
CRT displays are required to operate within a
range of different video frequencies (e.g. from 31
kHz to 64 kHz), thus also the switching frequency
of the SMPS will vary in that range.
In case of some failure, the power throughput may
be excessive without necessarily tripping the
pulse-by-pulse current limitation circuit because of
a high operating frequency.
For the sake of safety, it would be then desirable
to design the power stage of a converter (power
MOSFET, transformer, catch diode) so as to be
able to withstand the maximum power throughput
under failure conditions. However, this is a con-
siderable increase of size and cost.
The ”Constant Power” function of the L5993 al-
lows to overcome this problem. The device
changes the threshold of its pulse-by-pulse cur-
rent limitation circuit so as to maintain fairly con-
stant the power capability of a flyback converter
despite the changes of the switching frequency.
This is accomplished by clamping the output of
the error amplifier (VCOMP) to a value which de-
creases as the frequency of the signal fed into pin
1 (SYNC) builds up.
The frequency-to-voltage conversion needed to
achieve this functionality is performed by detect-
ing the peak voltage of the (synchronized) oscilla-
tor with a peak-holding circuit. One external ca-
pacitor only is required.
It is important to point out that shape, amplitude
and duration of the synchronization pulses are of
no concern with this technique.
APPLICATION INFORMATION
Detailed Pin Functions Description
Pin 1. SYNC (In/Out Synchronization). This func-
tion allows the IC’s oscillator either to synchronize
other controllers (master) or to be synchronized to
an external frequency (slave).
As a master, the pin delivers positive pulses dur-
ing the falling edge of the oscillator (see pin 2). In
slave operation the circuit is edge triggered. Refer
to fig. 21 to see how it works. When several IC
work in parallel no master-slave designation is
needed because the fastest one becomes auto-
matically the master.
During the ramp-up of the oscillator the pin is
pulled low by a 600
A internal sink current gener-
ator. During the falling edge, that is when the
pulse is released, the 600
A pull-down is discon-
nected. The pin becomes a generator whose
source capability is typically 7mA (with a voltage
still higher than 3.5V).
In fig. 20, some practical examples of synchroniz-
ing the L5993 are given.
Pin 2. RCT (Oscillator). A resistor (RT) and a ca-
pacitor (CT), connected as shown in fig. 21 set the
operating frequency fosc of the oscillator.
CT is charged through RT until its voltage reaches
3V, then is quickly internally discharged. As the
voltage has dropped to 1V it starts being charged
again.
The frequency can be established with the aid of
fig. 13 diagrams or considering the approximate
relationship:
fosc
1
CT
(0.693
RT + KT)
(1)
where KT is defined as:
KT
=
90, V15 = VREF
160 V15 = GND/OPEN
(2)
and is linked to the duration of the falling edge of
the sawtooth:
Td
30 10-9 +KT CT (3)
Td is also the duration of the sync pulses deliv-
L5993
RT
VREF
SYNC
RCT
L4981A
(MASTER)
L5993
(SLAVE)
RT
VREF
SYNC
RCT
ROSC
COSC
CT
L5993
(MASTER)
L4981A
(SLAVE)
SYNC
ROSC
CT
COSC
SYNC
(a)
(b)
(c)
RT
D97IN766B
CT
VREF
4
1
2
1
2
16
18
17
4
2
1
RCT
1
2
4
16
17
18
Figure 20. Sinchronizing the L5993.
L5993
8/22
相關PDF資料 |
PDF描述 |
|---|---|
| L6115 | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PZFM15 |
| L6114 | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDIP20 |
| L6205PD | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO20 |
| L6205D013TR | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO20 |
| L6206D | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L5993D | 功能描述:開關變換器、穩壓器與控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L5993D013TR | 功能描述:開關變換器、穩壓器與控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L5994 | 功能描述:電流型 PWM 控制器 Adj Triple Out Pwr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| L5994_02 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:ADJUSTABLE TRIPLE OUTPUT POWER SUPPLY CONTROLLER |
| L5994A | 功能描述:監控電路 ADJT TRIPLE OUTPUT POWER SUPPLY CNTLR RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。