- 您現在的位置：買賣IC網 > PDF目錄43899 > L5993 (STMICROELECTRONICS) 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDIP16 PDF資料下載
參數資料
| 型號： | L5993 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封裝： | DIP-16 |
| 文件頁數： | 2/22頁 |
| 文件大?。?/td> | 200K |
| 代理商： | L5993 |
Pin 5. VFB (Error Amplifier Inverting Input). The
feedback signal is applied to this pin and is com-
pared to the E/A internal reference (2.5V). The
E/A output generates the control voltage which
fixes the duty cycle.
The E/A features high gain-bandwidth product,
which allows to broaden the bandwidth of the
overall control loop, high slew-rate and current ca-
pability, which improves its large signal behavior.
Usually the compensation network, which stabi-
lizes the overall control loop, is connected be-
tween this pin and COMP (pin 6).
Pin 6. COMP (Error Amplifier Output). Usually,
this pin is used for frequency compensation and
the relevant network is connected between this
pin and VFB (pin 5). Compensation networks to-
wards ground are not possible since the L5993
E/A is a voltage mode amplifier (low output im-
pedance). See application ideas for some exam-
ple of compensation techniques.
Pin 7. SS (Soft-Start). At device start-up, a ca-
pacitor (Css) connected between this pin and
SGND (pin 12) is charged by an internal current
generator, ISSC, up to about 7V. During this
ramp, the E/A output is clamped by the voltage
across Css itself and allowed to rise linearly, start-
ing from zero, up to the steady-state value im-
posed by the control loop. The maximum time in-
terval during which the E/A is clamped, referred to
as soft-start time, is approximately:
Tss
3
Rsense IQpk
ISSC
Css
(6)
where Rsense is the current sense resistor (see pin
13) and IQpk is the switch peak current (flowing
through Rsense), which depends on the output
load. Usually, CSS is selected for a TSS in the or-
der of milliseconds.
As mentioned before, the soft-start intervenes
also in case of severe overload or short circuit on
the output. Referring to fig. 23, pulse-by-pulse
current limitation is somehow effective as long as
the ON-time of the power switch can be reduced
(from A to B). After the minimum ON-time is
reached (from B onwards) the current is out of
control.
To prevent this risk, a comparator trips an over-
current handling procedure, named ’hiccup’ mode
operation, when a voltage above 1.2V (point C) is
detected on current sense input (ISEN, pin 13).
Basically, the IC is turned off and then soft-started
as long as the fault condition is detected. As a re-
sult, the operating point is moved abruptly to D,
creating a foldback effect. Fig. 24 illustrates the
operation.
The oscillation frequency appearing on the soft-
VOUT
TON
D.C.M.
C.C.M.
D
A
B
C
IQpk
TON(min)
1-2 IQpk
IQpk(max)
I
OUT
I
SHORT
I
OUT(max)
D97IN495
Figure 23. Regulation characteristic and re-
lated quantities
7V
Thic
time
SHORT
IOUT
ISEN
FAULT
SS
5V
0.5V
D98IN986
Figure 24. Hiccup mode operation.
L5993
10/22
相關PDF資料 |
PDF描述 |
|---|---|
| L6115 | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PZFM15 |
| L6114 | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDIP20 |
| L6205PD | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO20 |
| L6205D013TR | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO20 |
| L6206D | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L5993D | 功能描述:開關變換器、穩壓器與控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L5993D013TR | 功能描述:開關變換器、穩壓器與控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L5994 | 功能描述:電流型 PWM 控制器 Adj Triple Out Pwr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| L5994_02 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:ADJUSTABLE TRIPLE OUTPUT POWER SUPPLY CONTROLLER |
| L5994A | 功能描述:監控電路 ADJT TRIPLE OUTPUT POWER SUPPLY CNTLR RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。