參數資料
型號： KSZ9021GN-EVAL
廠商： Micrel Inc
文件頁數： 13/53頁
文件大小： 0K
描述： BOARD EVALUATION FOR KSZ9021GN
標準包裝： 1
主要目的： 接口，以太網控制器（PHY 和 MAC）
嵌入式： 否
已用 IC / 零件： KSZ9021GN
已供物品： 板
相關產品： 576-3789-ND - TXRX GIG ETH GMII/MII 64-QFN
KSZ9021GN TR-ND - TXRX ETHERNET GB GMII/MII 64MLF
576-3635-ND - TXRX ETHERNET GB GMII/MII 64-MLF
其它名稱： 576-3873
Micrel, Inc.
KSZ9021GN
September 2010
20
M9999-091010-1.1
Figure 3. Auto-Negotiation Flow Chart
For 1000Base-T mode, auto-negotiation is required and always used to establish a link. During 1000Base-T auto-
negotiation, the Master and Slave configuration is first resolved between link partners, and then the link is established
with the highest common capabilities between link partners.
Auto-negotiation is enabled by default at power-up or after hardware reset. Afterwards, auto-negotiation can be enabled
or disabled through register 0 bit 12. If auto-negotiation is disabled, the speed is set by register 0 bits 6 and 13, and the
duplex is set by register 0 bit 8.
If the speed is changed on the fly, the link goes down and either auto-negotiation or parallel detection will initiate until a
common speed between KSZ9021GN and its link partner is re-established for a link.
If link is already established and there is no change of speed on the fly, then the changes will not take effect unless
either auto-negotiation is restarted through register 0 bit 9, or a link down to link up transition occurs (i.e., disconnecting
and reconnecting the cable).
After auto-negotiation is completed, the link status is updated in register 1 and the link partner capabilities are updated
in registers 5, 6, and 10.
The auto-negotiation finite state machines employ interval timers to manage the auto-negotiation process. The duration
of these timers under normal operating conditions are summarized in the following table.
相關PDF資料
PDF描述
V24C8C100BF CONVERTER MOD DC/DC 8V 100W
342A112-100-0 BOOT MOLDED
H4PXS-2418M DIP CABLE - HDP24S/AE24M/X
H2PXS-2418M DIP CABLE - HDP24S/AE24M/X
202F274-71-0 BOOT MOLDED
相關代理商/技術參數
參數描述
KSZ9021GNI 功能描述:以太網 IC Gigabit Ethernet Transceiver with GMII/MII, I-Temp RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ9021GQ 功能描述:以太網 IC Gigabit Ethernet Transceiver with GMII/MII, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ9021GQI 功能描述:以太網 IC Gigabit Ethernet Transceiver w/ GMII/MII, I-Temp RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ9021RL 功能描述:以太網 IC Gigabit Ethernet Transceiver with GMII RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ9021RL-EVAL 制造商:Micrel Inc 功能描述:GIGABIT ETHERNET TRANSCEIVER W 制造商:Micrel Inc 功能描述:KIT EVALUATION FOR KSZ9021RL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*