參數資料
型號: KSZ8842-16MQL-EVAL
廠商: Micrel Inc
文件頁數: 86/141頁
文件大小: 0K
描述: BOARD EVALUATION KSZ8842-16MQL
標準包裝: 1
主要目的: 接口,以太網控制器(PHY 和 MAC)
嵌入式:
已用 IC / 零件: KSZ8842-16MQL
主要屬性: 2 個端口,100BASE-TX/10BASE-T,管理型
次要屬性: 8/16 位接口,LinkMD 線纜診斷
已供物品: 板,CD,文檔,電源
產品目錄頁面: 1114 (CN2011-ZH PDF)
相關產品: 576-3076-ND - IC MAC CTLR 2PORT ETH 100-LFBGA
KSZ8842-32MQLA6-ND - IC SWITCH 10/100 32BIT 128PQFP
576-1479-ND - IC SWITCH 10/100 32BIT 128PQFP
576-1478-5-ND - IC SWITCH 10/100 16BIT 128PQFP
其它名稱: 576-1634
Micrel, Inc.
KSZ8842-16/32 MQL/MVL/MVLI/MBL
October 2007
49
M9999-102207-1.9
The format for ConfigParam is shown in Table 13.
Bit
Bit Name
Description
15 -2
Reserved
1
Clock_Rate
Internal clock rate selection
0: 125 MHz
1: 25 MHz
Note: At power up, this chip operates on 125 MHz clock. The internal frequency can be
dropped to 25 MHz via the external EEPROM.
0
ASYN_8bit
Async 8-bit or 16-bit bus select
1= bus is configured for 16-bit width
0= bus is configured for 8-bit width
(32-bit width, KSZ8842-32, don’t care this bit setting)
Table 13. ConfigParam Word in EEPROM Format
Loopback Support
The KSZ8842M provides loopback support for remote diagnostic of failure. In loopback mode, the speed at both PHY
ports will be set to 100BASE-TX full-duplex mode. Two types of loopback are supported: Far-end Loopback and Near-end
(Remote) Loopback.
Far-end Loopback
Far-end loopback is conducted between the KSZ8842M’s two PHY ports. The loopback path starts at the “Originating.”
PHY port’s receive inputs (RXP/RXM), wraps around at the “l(fā)oopback” PHY port’s PMD/PMA, and ends at the
“Originating” PHY port’s transmit outputs (TXP/TXM).
Bit [8] of registers P1CR4 and P2CR4 is used to enable far-end loopback for ports 1 and 2, respectively. Alternatively, Bit
[14] of registers P1MBCR and P2MBCR can also be used to enable far-end loopback. The port 2 far-end loopback path is
illustrated in the Figure 15.
Near-end (Remote) Loopback
Near-end (Remote) loopback is conducted at either PHY port 1 or PHY port 2 of the KSZ8842M. The loopback path starts
at the PHY port’s receive inputs (RXPx/RXMx), wraps around at the same PHY port’s PMD/PMA, and ends at the PHY
port’s transmit outputs (TXPx/TXMx).
Bit [1] of registers P1PHYCTRL and P2PHYCTRL is used to enable near-end loopback for ports 1 and 2, respectively.
Alternatively, Bit [9] of registers P1SCSLMD and P2SCSLMD can also be used to enable near-end loopback. The both
ports 1 and 2 near-end loopback paths are illustrated in the following Figure 16.
相關PDF資料
PDF描述
222K121-12-0 BOOT MOLDED
NLCV32T-680K-PF INDUCTOR POWER 68UH 1210
0210490359 CABLE JUMPER 1.25MM .229M 28POS
101-1218 KIT APPLCTN RABBITCORE RCM4010
0982660995 CBL 29POS 0.5MM JMPR TYPE A 5"
相關代理商/技術參數
參數描述
KSZ8842-16MVL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-16MVL TR 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-16MVL-EVAL 功能描述:BOARD EVALUATION KSZ8842-16MVL RoHS:是 類別:編程器,開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理,電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
KSZ8842-16MVLI 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842-16MVLI TR 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray